This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
advanced-misc [2022/02/17 15:13] – grammar, spelling, clarity hogwild | advanced-misc [2023/09/25 19:03] – hogwild | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== Miscellaneous ====== | ====== Miscellaneous ====== | ||
- | This page allows | + | In this menu, you can tweak some secondary |
\\ | \\ | ||
- | [[https://wiki.freshtomato.org/ | + | **Boot Wait Time * :** This is the time period during which a router can be accessed using the included CFE webserver. This refers to the bootstrap portion of the process, or the loading of code before the Operating system loads. If you need to delay the s boot process (to stay in internal webserver CFE mode), change this setting. In rare circumstances, |
- | \\ | + | {{: |
- | **Boot Wait Time *** - Is the time period when a router can be accessed using the included CFE webserver. This refers to the bootstrap portion of the process, or the loading of code before the OS. If you need to delay FreshTomato' | + | \\ {{: |
- | **WAN Port Speed *** - Enables you to choose between autonegotiate (Default) mode on the WAN port, or forcing a specific combination of speed/ | + | CTF lets bridges use an alternative forwarding method |
- | \\ | + | With CTF enabled, the router starts to send out transmission frames as soon as it receives its destination. However, the router relies on the client device to tell it whether the data is corrupted for resend. This restriction can cause problems with a few common home uses. Note that enabling CTF will disable QoS and Bandwidth Limiter. This is because the switching part of the packet bypasses parts of the standard Linux iptable chains. |
- | [[https://wiki.freshtomato.org/lib/ | + | When you have CTF disabled, the router will store the entire frame before sending it out to its destination. When this happens: |
+ | |||
+ | * The holding period may require more of the router' | ||
+ | * WAN-to-LAN performance depends more on the router model in use. | ||
+ | * | ||
+ | |||
+ | CTF/FastNAT is support as follows: | ||
+ | |||
+ | * ARM Routers (like the RT-AC68U, RT-AC3200, R7000) support CTF. | ||
+ | * MIPS RT-N routers (like the E4200v1, RT-N16) can use Broadcom FastNAT | ||
+ | * FastNAT is a similar function to forward at accelerated speeds. | ||
+ | * MIPS RT-AC routers (like the RT-AC66U) do not support CTF or FastNAT. | ||
\\ | \\ | ||
- | **CTF (Cut-Through Forwarding)** - If set, this will enable hardware acceleration. For example, this would allow you to use your FreshTomato device | + | On ARM-based devices, you can expect performance |
- | CTF is only available for ARM Routers (like the RT-AC68U, RT-AC3200, R7000, and so on). MIPS RT-N routers (like the E4200v1, RT-N16, RT-N15U, etcetera) can use Broadcom FastNAT. MIPS RT-AC routers | + | \\ **Enable Jumbo Frames * :** This option allows you to increase |
- | **Enable | + | The default size for Jumbo Frames |
- | **Jumbo Frame Size *** - There' | + | The jumbo frames feature is only supported in 1000 Mbit/s mode. Also, a gigabit switch uses more memory when this feature is enabled. This will influence system performance, |
+ | |||
+ | **Jumbo Frame Size:** If disabled, the default | ||
+ | |||
+ | Generally, enable | ||
+ | |||
+ | You are strongly | ||
+ | |||
+ | \\ | ||
+ | |||
+ | \\ | ||
\\ | \\ | ||