This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
advanced-vlan [2024/09/25 21:22] – [VLAN (IEEE 802.1Q)] -condense hogwild | advanced-vlan [2025/03/29 19:12] (current) – [VLAN Wireless] -Replace screenshot with one in Tomato theme hogwild | ||
---|---|---|---|
Line 14: | Line 14: | ||
===== VLAN Ethernet (Basic Configuration Information) ===== | ===== VLAN Ethernet (Basic Configuration Information) ===== | ||
- | * VLAN - the VLAN's unique identifier. (VLAN 0 to VLAN 15) | + | * VLAN - this VLAN's unique identifier. (VLAN 0 to VLAN 15) \\ \\ |
- | * VID - allows overriding " | + | * VID - allows overriding " |
- | * Ports 1 - 4 and WAN - specify which Ethernet ports will be members of this VLAN. | + | * Ports 1 to 4 and WAN - specify which Ethernet ports will be members of this VLAN. \\ \\ |
- | * Tagged - enable 802.1Q tagging of Ethernet frames on a particular port/ | + | * Tagged - enable 802.1Q tagging of Ethernet frames on a particular port/ |
- | * Default - the VLAN ID assigned to untagged frames that the router receives. | + | * Default - the VLAN ID assigned to untagged frames that the router receives. |
- | * Bridge - determines if this VLAN ID should be treated as WAN, part of a LAN bridge \\ or just left as is (a member of an 802.1Q trunk, | + | * Bridge - determines if this VLAN ID should be treated as WAN, part of a LAN bridge \\ or just left as is (member of an 802.1Q trunk, managed manually via scripts). |
Line 26: | Line 26: | ||
This section contains the assignments of wireless interfaces to various LAN bridges. | This section contains the assignments of wireless interfaces to various LAN bridges. | ||
- | It is recommended that you determine/verify the correct settings on the [[: | + | Always check/verify the correct settings on the [[: |
The following settings are also mandatory: | The following settings are also mandatory: | ||
- | | + | \\ |
- | * One VID must be selected as the default. | + | |
- | * Avoid using VID: " | + | |
- | * Avoid using VID: " | + | * One VID must be selected as the default. |
+ | * Avoid using VID: " | ||
+ | * Avoid using VID: " | ||
\\ \\ **Configuration example for German Telekom ISP** | \\ \\ **Configuration example for German Telekom ISP** | ||
- | Europe' | + | \\ |
- | {{: | + | GT supports a dual-stack setup (IPv4 & IPv6). For the WAN Port, a VLAN tag with a value of 7 (VID 7) is required. |
+ | {{:: | ||
- | ===== VLAN Notes ===== | ||
- | As described above, for VLANs to function properly, please** use FreshTomato 2021.8 or later**. \\ Older versions, (such as Shibby/ | + | ===== VLAN Notes and Troubleshooting ===== |
- | === PPPoE Connections with FreshTomato 2021.7 and older === | + | As mentioned earlier, for VLANs to function properly, please** use FreshTomato 2021.8 or later**. Older versions like AdvancedTomato, |
+ | |||
+ | **PPPoE Connections with FreshTomato 2021.7 and older** | ||
PPPoE connections work only when the following workaround is implemented: | PPPoE connections work only when the following workaround is implemented: | ||
- | //Example 1//: You are using FreshTomato 2021.7 to connect to German Telekom ISP. \\ German Telekom uses PPPoE with VID: " | + | \\ **//Example 1//:** FreshTomato 2021.7 |
- | \\ //Example 2//: You are using FreshTomato 2021.7 to connect to Freedom Internet. \\ Freedom uses PPPoE , and VLAN: " | + | |
+ | |||
+ | See: [[https:// | ||
\\ | \\ | ||
- | //Example 3//: You are using FT 2021.7 to connect to Vivo FTTH (Brazil). \\ (Vivo use PPPoE, and VLAN: " | + | **//Example 3//:** FreshTomato |
+ | |||
+ | See [[https:// | ||
- | Starting with release 2021.8, you can select | + | Since release 2021.8, you can select/use any VLAN from 0 to 15. (See example in above picture |
\\ | \\ | ||