Differences

This shows you the differences between two versions of the page.

--- advanced-vlan [2025/03/29 17:09] – [VLAN Wireless] hogwild
+++ advanced-vlan [2025/03/29 19:12] (current) – [VLAN Wireless] -Replace screenshot with one in Tomato theme hogwild
@@ Line 14: / Line 14: @@
 ===== VLAN Ethernet (Basic Configuration Information) =====
-  * VLAN - this VLAN's unique identifier. (VLAN 0 to VLAN 15)
+  * VLAN - this VLAN's unique identifier. (VLAN 0 to VLAN 15) \\ \\
-  * VID - allows overriding "traditional" VLAN/VID mapping (Such as: VLAN 4 to VID 4) \\ with arbitrary VIDs for each VLAN. (Use "0" for "regular" mappings instead).
+  * VID - allows overriding "traditional" VLAN/VID mapping (Such as: VLAN 4 to VID 4) \\ with arbitrary VIDs for each VLAN. (Use "0" for "regular" mappings instead). \\
-  * Ports 1 to 4 and WAN - specify which Ethernet ports will be members of this VLAN.
+  * Ports 1 to 4 and WAN - specify which Ethernet ports will be members of this VLAN. \\ \\
-  * Tagged - enable 802.1Q tagging of Ethernet frames on a particular port/VLAN.
+  * Tagged - enable 802.1Q tagging of Ethernet frames on a particular port/VLAN. \\ \\
-  * Default - the VLAN ID assigned to untagged frames that the router receives.
+  * Default - the VLAN ID assigned to untagged frames that the router receives. \\ \\
   * Bridge - determines if this VLAN ID should be treated as WAN, part of a LAN bridge \\ or just left as is (member of an 802.1Q trunk, managed manually via scripts).
@@ Line 26: / Line 26: @@
 This section contains the assignments of wireless interfaces to various LAN bridges.
-You should check/verify the correct settings on the [[:virtual_wireless|Virtual Wireless]] and [[:basic-network|Network]] menus to ensure proper VLAN operation.
+Always check/verify the correct settings on the [[:virtual_wireless|Virtual Wireless]] and [[:basic-network|Network]] menus to ensure proper VLAN operation.
 The following settings are also mandatory:
@@ Line 32: / Line 32: @@
  \\
-  * One VID must be assigned to the WAN interface. \\
+  * One VID must be assigned to the WAN interface. \\ \\
-  * One VID must be selected as the default. \\
+  * One VID must be selected as the default. \\ \\
-  * Avoid using VID: "0" to prevent 802.1Q compatibility issues. \\ 802.1Q specifies that frames tagged with "0" don't belong to any VLAN.\\ (This tag contains only user priority details).  [[https://en.wikipedia.org/wiki/IEEE_802.1Q|Wikipedia: 802.11Q]]
+  * Avoid using VID: "0" to prevent 802.1Q compatibility issues. \\ 802.1Q specifies that frames tagged with "0" don't belong to any VLAN.\\ (This tag contains only user priority details).  [[https://en.wikipedia.org/wiki/IEEE_802.1Q|Wikipedia: 802.11Q]] \\ \\
   * Avoid using VID: "1". Some vendors label it "special" \\ or "reserved" for management.
@@ Line 43: / Line 43: @@
 GT supports a dual-stack setup (IPv4 & IPv6). For the WAN Port, a VLAN tag with a value of 7 (VID 7) is required.
-{{:telekom_example_vid_7.png?852}}
+{{::advanced-vlan-telekom_example.png?800}}

FreshTomato Wiki

User Tools

Site Tools

Differences

Page Tools