This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
advanced-wireless [2023/09/25 20:49] – [Protected Management Frames] -explain PMF basics/formatting hogwild | advanced-wireless [2024/03/02 18:01] (current) – [Advanced Wireless] Fix Network link hogwild | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== Advanced Wireless ====== | ====== Advanced Wireless ====== | ||
- | The Advanced Wireless menu contains settings for advanced tuning of WiFi interfaces. Changing settings from defaults is not recommended unless you are experienced with advanced WiFi settings. Default dropdown settings are noted with an asterisk (*). For basic WiFi settings, see the the [[basic-network|Network]] menu wiki page. \\ \\ \\ {{: | + | The Advanced Wireless menu contains settings for advanced tuning of WiFi interfaces. Changing settings from defaults is not recommended unless you are experienced with advanced WiFi settings. Default dropdown settings are noted with an asterisk (*). For basic WiFi settings, see the the [[:basic-network|Network]] menu wiki page. \\ \\ \\ {{: |
Line 177: | Line 177: | ||
* E0 / 946 - Country: E0 AND Country Rev: 946 (Asus default setup for Germany [alias " | * E0 / 946 - Country: E0 AND Country Rev: 946 (Asus default setup for Germany [alias " | ||
* Q2 / 992 - Country: Q2 AND Country Rev: 992 (Asus default setup for USA [alias " | * Q2 / 992 - Country: Q2 AND Country Rev: 992 (Asus default setup for USA [alias " | ||
+ | * Q1 / 984 - Country: Q1 AND Country Rev: 984 (Asus default setup for USA [alias " | ||
* TBD. - CFE default value used | * TBD. - CFE default value used | ||
Line 333: | Line 334: | ||
(Default: 0 / Disabled) | (Default: 0 / Disabled) | ||
- | After enabling the Roaming Assistant, you can define the value for disconnecting clients with RSSI lower than -XY dBm (Valid range: -90 to -45) from your WiFi radio interface (eth1/ | + | This function allows you " |
- | Support for this option | + | Support for this option |
\\ | \\ | ||
Line 519: | Line 520: | ||
* opt. 1 AND opt. 2 AND opt. 3 (All option enabled) \\ | * opt. 1 AND opt. 2 AND opt. 3 (All option enabled) \\ | ||
- | \\ | + | When Access Points/ |
+ | |||
+ | Starting with with WiFi protocol 802.11ac, AC-PHY Interference Mitigation mechanisms can use 3 different strategies, or combinations of them, to reduce interference from other " | ||
{{: | {{: | ||
Line 569: | Line 572: | ||
However, WMM is a requirement of the 802.11n, 802.11ac and 802.11ax specifications. Disabling it will cause fully WMM-compliant clients to fall back to 802.11a/g legacy rates (of 54 Megabits/ | However, WMM is a requirement of the 802.11n, 802.11ac and 802.11ax specifications. Disabling it will cause fully WMM-compliant clients to fall back to 802.11a/g legacy rates (of 54 Megabits/ | ||
- | Also note that if you some Apple products, such as iPhone, iPad, iPod touch, or Apple TV may not be able to connect to WiFi via the 802.1 protocl unless WMM is enabled.\\ | + | Also note that if you some Apple products, such as iPhone, iPad, iPod touch, or Apple TV may not be able to connect to WiFi via the 802.1 protocl unless WMM is enabled.\\ |