Differences

This shows you the differences between two versions of the page.

--- basic-ipv6 [2023/06/24 20:10] – [IPv6 DUID Type] -clarity, condense, grammar hogwild
+++ basic-ipv6 [2023/06/24 20:55] (current) – [IPv6 DUID Type] hogwild
@@ Line 19: / Line 19: @@
 This configuration method is one of the most commonly used. It provides native IPv6 connectivity for your network. It allows the ability to assign different IPv6 address ranges for bridge 0 (br0) to 3 (br3) if you're given a prefix with length smaller than 64 (for example 60 or 56) from your provider. The option to assign IPv6 address ranges for bridge 1 (br1) to 3 (br3) is only visible if the bridges already exist. Check your configuration in the //Basic///[[basic-network|Network]] menu to learn more.
-**Configuration example for German Telekom ISP**
+ \\
-German Telekom, Europe's biggest telecom company, supports a dual-stack setup (IPv4 & IPv6). By default, it provides a prefix length of 56 for regular consumers. A prefix length of 64 (the default configuration for FreshTomato) will also work, but eliminates the possibility of assigning different IPv6 address ranges for bridge 1 (br1) to 3 (br3).
+Example Configuration: German Telekom
- \\
+German Telekom is Europe's biggest telecom company. It supports a dual-stack setup (IPv4 & IPv6). By default, it provides a prefix length of 56 for regular consumers. A prefix length of 64 (FreshTomato's default) will also work. However, that eliminates the possibility of assigning different IPv6 address ranges for bridge 1 (br1) to 3 (br3).
-{{:ft_basic_ipv6_dhcpv6_01.png}}
+ \\ {{::basic-ipv6-dhcpv6_with_pd-2023.2.jpg?736}}
  \\
@@ Line 31: / Line 31: @@
  \\
-**Extended options are available for IPv6 DHCPv6 PD - if bridges 1 (br1) to 3 (br3) exist AND if the prefix length is smaller than 64 (for example 60 or 56)**
+Extended options are available in this mode. If bridges 1 (br1) through 3 (br3) exist, and if the prefix length is smaller than 64, you can enable IPv6 subnets for these bridges, as seen below.
- \\
+{{::ft_basic_ipv6_dhcpv6_02-2020.7.jpg?731}}
-{{:ft_basic_ipv6_dhcpv6_02.png}}
@@ Line 64: / Line 62: @@
 ===== IPv6 DUID Type =====
-Every DHCP client and server have a DHCP Unique Identifier, or "DUID". The DHCP server uses the DUID to identify the clients for the selection of configuration parameters.
+Every DHCP client and server have a DHCP Unique Identifier, or "DUID". The DHCP server uses the DUID to identify clients for the selection of configuration parameters.
 Options:
@@ Line 71: / Line 69: @@
   * DUID-LLT
-DUID-LL will use the LAN (eth0) MAC address and will not change (always static) over time. DUID-LLT will, in addition, include time value, and will change on every reboot or reconnect of the WAN interface. You can see the currently used DUID at the GUI Status Overview.
+ \\
+DUID-LL will use the LAN (eth0) MAC address and will not change (remain static) over time. DUID-LLT will, in addition, include time value, and will change on every reboot or reconnect of the WAN interface. You can see the currently used DUID on the Status Overview menu.
 Support for this option started with release 2022.4.
-Note: DUID-EN or DUID-UUID or a custom DUID are currently not supported.
+Note: DUID-EN, DUID-UUID or custom DUIDs are currently not supported.
+ \\
 {{:pasted:20220722-092300.png?400}}
+ \\
 ===== Prefix Length =====

FreshTomato Wiki

User Tools

Site Tools

Differences

Page Tools