FreshTomato Wiki

User Tools

Site Tools

Trace:
hardware_compatibility

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
hardware_compatibility [2023/01/07 00:11] – Editing E3200 nvram size. txnativehardware_compatibility [2025/05/07 15:42] (current) – [Does FreshTomato support your hardware?] -Spelling, condense hogwild
Line 1: Line 1:
-====== Hardware (Router) Compatibility ======+====== Hardware compatibility ======
  
- \\  The FreshTomato project offers support for the following routers:  \\   \\+===== Does FreshTomato support your hardware? ===== 
 + 
 +  - Look for your device in the [[hardware_compatibility#hardware_compatibility_table|Hardware Compatibility Table]] below. \\ It's the authoritative source for hardware support. Note your //hardware revision. //[(hardrev)] \\ It too must be included there. If your device is in the table, it's\\ officially supported. Review any notes in the table. There are \\ important details recorded there. \\ \\  
 +  - Only devices with **Broadcom (ARM or MIPS architecture) chipsets** are supported. \\ \\ Use a reliable source to confirm your device uses them, such as  \\ a database like [(refdbs)]  [[https://wikidevi.wi-cat.ru/|WikiDevi]] or [[https://techinfodepot.shoutwiki.com/|TechInfoDepot]]. \\ There, search for your model. If it's in the search results, confirm that \\ "Broadcom" is listed in all required fields below.  \\ \\ - CPU1 \\ - Switch \\ - All fields whose names conform to these formats: \\ [(chipids)]ETH chip<ff serif>//X//</ff> WI<ff serif>//X//</ff> chip<ff serif>//X//</ff>  \\ \\ After confirming this, you can post a request on the forum to add support for it. \\ In your post, include links to the database references you checked.\\ \\  
 +  - [[https://www.linksysinfo.org/index.php?search&t=post&c%5Bchild_nodes%5D=1&c%5Bnodes%5D%5B0%5D=33&o=date|Search the forum]] for a (partly) working build in development. \\ If your device is Broadcom-based but isn't in the table, someone might \\ be working on adding support for it. \\ \\ Alternatively, forum members may know whether a build for another model \\ may work //to some degree// on your device.[(wipbuilds)]  \\ \\ Be alert for differences in hardware revision. Different hardware revisions \\ may use radically different electronics. With some models, there may be risks \\ involved. Read all details carefully. \\ \\ 
 + 
 +[(hardrev>Sometimes one hardware version/revision of the same model is supported, but others aren't. For example, the "A1" version is supported, but "B2" isn't. Often, this is because different revisions of the same model contain different chipsets. FreshTomato only supports devices using **Broadcom chipsets of ARM or MIPS architecture**. \\ \\ )] [(refdbs>These sites also maintain lists of devices compatible with FreshTomato (lists of Tomato-supported devices at [[https://wikidevi.wi-cat.ru/List_of_Tomato_firmware_supported_devices|WikiDevi]] and [[https://techinfodepot.shoutwiki.com/wiki/List_of_Tomato_firmware_supported_devices|TechInfoDepot]]). However, their information is sourced here and merely reconstructed in their databases. Thus, contradictions between their data and data on this page indicate the presence of incomplete or incorrect information elsewhere, not here. \\ \\ )] [(chipids>Where <ff serif>//X//</ff> is a digit indicating a series ordinal such as first or second. For any given device, the first wireless chip on a given band would be labelled "WI**1** chip**1**". Another chip on that same band would be "WI**1** chip**2**". A chip on a different band would be labelled "WI**2** chip**1**". For an example, visit the [[https://wikidevi.wi-cat.ru/ASUS_RT-AC3100|Asus RT-AC3100]] entry on WikiDevi. \\ \\ )] [(wipbuilds>If the effort is successful and has enough testers, this will usually result in the device being added to the compatibility table. The FreshTomato developers welcome the upstreaming of such work.)] 
 + 
 +==== Notes ==== 
 + 
 +~~REFNOTES~~ 
 + 
 +===== Hardware Compatibility Table ===== 
 + 
 +  //**NOTE:** You may need to zoom out in your browser to see content in the Notes column.//
  
 <sortable> <sortable>
  
-^ Model  ^  Rev  ^ CPU Type ^ MHz ^ CPUs ^ LAN ^ USB2 ^ USB3 ^ WiFi ^ Flash ^ NVRAM ^ RAM ^ Build ^ Notes ^ +^ Manufacturer \\ Model \\ ^  Hardware Rev.  ^  Arch.  ^  CPUs  ^  LAN  ^  USB 2.0/3.0  ^  WiFi Class  ^  Flash  ^  NVRAM  ^  RAM  ^  Build \\ (SDK) \\ ^  Notes  ^ 
-| Asus DSL-AC68U |   | ARM | 800 | 2 | 1000 | 1 | 1 | AC1900 | 128MB | 64KB | 256MB | K26ARM | [[https://www.linksysinfo.org/index.php?threads/ft-on-asus-dsl-ac68u-work-in-progress.75080| Supported from 2022.3 ]] \\ **no xDSL support**, this device is to be used as a router only. WAN port is initialized to LAN port 1 | +| ASUS \\ **DSL‑AC68U**  |   |  ARM  |  800Mhz ×2  |  1GbE ×4  |  1 / 1  |  AC1900  |  128MB  |  64KB  |  256MB  |  K26ARM (SDK6.37)  | Supported from 2022.3. ([[https://www.linksysinfo.org/index.php?threads/ft-on-asus-dsl-ac68u-work-in-progress.75080|forum thread]]) \\ \\ **No DSL support**; device acts as router only with WAN port remapped as LAN1.  | 
-| Asus RT-N10P |   | MIPS-R2 | 300 | 1 | 100 | - | - | N300 | 8MB | 32KB | 32MB | K26RT-N |   | +| ASUS \\ **RT‑N10P**  |   |  MIPS R2  |  300Mhz ×1  |  100MbE ×4  |  ‒ / ‒  |  N300  |  8MB  |  32KB  |  32MB  |  K26RT-N (SDK5.110)  |   | 
-| Asus RT-N10U | A1/B1/C1 | MIPS-R2 | 300 | 1 | 100 | 1 | - | N300 | 8MB | 32KB | 32MB | K26RT-N |   | +| ASUS \\ **RT‑N10U**  |  A1 / B1 / C1  |  MIPS R2  |  300Mhz ×1  |  100MbE ×4  |  1 / ‒  |  N300  |  8MB  |  32KB  |  32MB  |  K26RT-N (SDK5.110)  |   | 
-| Asus RT-N12 | A1 | MIPS-R2 | 300 | 1 | 100 | - | - | N300 | 4MB | 32KB | 32MB | K26 |   | +| ASUS \\ **RT‑N12**  |  A1  |  MIPS R2  |  300Mhz ×1  |  100MbE ×4  |  ‒ / ‒  |  N300  |  4MB  |  32KB  |  32MB  |  K26 (SDK5.10)  |   | 
-| Asus RT-N12 | B1/C1/D1 | MIPS-R2 | 300 | 1 | 100 | - | - | N300 | 8MB | 32KB | 32MB | K26RT-N |   | +| ASUS \\ **RT‑N12**  |  B1 / C1 / D1  |  MIPS R2  |  300Mhz ×1  |  100MbE ×4  |  ‒ / ‒  |  N300  |  8MB  |  32KB  |  32MB  |  K26RT-N (SDK5.110)  |   | 
-| Asus RT-N12HP | A1/B1 | MIPS-R2 | 300 | 1 | 100 | - | - | N300 | 8MB | 32KB | 32MB | K26RT-N | Support for High Power model added in 2020.4 | +| ASUS \\ **RT‑N12HP**  |  A1 / B1  |  MIPS R2  |  300Mhz ×1  |  100MbE ×4  |  ‒ / ‒  |  N300  |  8MB  |  32KB  |  32MB  |  K26RT-N (SDK5.110)  | Support for High Power model added in 2020.4.  | 
-| Asus RT-N12K |   | MIPS-R2 | 300 | 1 | 100 | - | - | N300 | 8MB | 32KB | 32MB | K26RT-N |   | +| ASUS \\ **RT‑N12K**  |   |  MIPS R2  |  300Mhz ×1  |  100MbE ×4  |  ‒ / ‒  |  N300  |  8MB  |  32KB  |  32MB  |  K26RT-N (SDK5.110)  |   | 
-| Asus RT-N12VP |   | MIPS-R2 | 300 | 1 | 100 | - | - | N300 | 8MB | 32KB | 32MB | K26RT-N |   | +| ASUS \\ **RT‑N12VP**  |   |  MIPS R2  |  300Mhz ×1  |  100MbE ×4  |  ‒ / ‒  |  N300  |  8MB  |  32KB  |  32MB  |  K26RT-N (SDK5.110)  |   | 
-| Asus RT-N15U |   | MIPS-R2 | 500 | 1 | 1000 | 1 | - | N300 | 8MB | 32KB | 64MB | K26RT-N |   | +| ASUS \\ **RT‑N15U**  |   |  MIPS R2  |  500Mhz ×1  |  1GbE ×4  |  1 / ‒  |  N300  |  8MB  |  32KB  |  64MB  |  K26RT-N (SDK5.110)  |   | 
-| Asus RT-N16 |   | MIPS-R2 | 480 | 1 | 1000 | 2 | - | N300 | 32MB | 32KB | 128MB | K26 or K26RT-N | 32K NVRAM build required. | +| ASUS \\ **RT‑N16**  |   |  MIPS R2  |  480Mhz ×1  |  1GbE ×4  |  2 / ‒  |  N300  |  32MB  |  32KB  |  128MB  |  K26 (SDK5.10) or K26RT-N (SDK5.110)  | 32K NVRAM build required  | 
-| Asus RT-AC1750 | B1 | ARM | 1000 | 2 | 1000 | 1 | 1 | AC1750 | 128MB | 64KB | 256MB | K26ARM | Supported from 2021.3. | +| ASUS \\ **RT‑N18U**  |   |  ARM  |  800Mhz ×1  |  1GbE ×4  |  1 / 1  |  N600  |  128MB  |  64KB  |  256MB  |  K26ARM (SDK6.37)  | Use images ending with <typo bg: #002d38; fc: #819500; ff: monospace; fs: 14px; lh: 1.0; sp: nowrap; va: text-bottom;>…‑64K‑NOSMP.trx</typo>.  | 
-| Asus RT-N18U |   | ARM | 800 | 1 | 1000 | 1 | 1 | N600 | 128MB | 64KB | 256MB | K26ARM | Single core (please use images ending with "…-64K-NOSMP.trx"). | +| ASUS \\ **RT‑N53**  |   |  MIPS R2  |  300Mhz ×1  |  100MbE ×4  |  ‒ / ‒  |  N600  |  8MB  |  32KB  |  32MB  |  K26RT-N (SDK5.110)  |   | 
-| Asus RT-N53 |   | MIPS-R2 | 300 | 1 | 100 | - | - | N600 | 8MB | 32KB | 32MB | K26RT-N |   | +| ASUS \\ **RT‑N66U**  |  B1  |  MIPS R2  |  600Mhz ×1  |  1GbE ×4  |  2 / ‒  |  N900  |  32MB  |  64KB  |  256MB  |  K26RT-N (SDK5.110) or K26RT-AC  |   | 
-| Asus RT-N66U |   | MIPS-R2 | 600 | 1 | 1000 | 2 | - | N900 | 32MB | 64KB | 256MB | K26RT-N or K26RT-AC |   | +| ASUS \\ **RT‑N66U**  |  C1 (a/k/a B2)  |  ARM  |  1Ghz ×2  |  1GbE ×4  |  1 / 1  |  N900  |  128MB  |  64KB  |  256MB  |  K26ARM (SDK6.37)  | Supported from 2020.8.  | 
-| Asus RT-N66U | C1 (B2) | ARM | 1000 | 2 | 1000 | 1 | 1 | N900 | 128MB | 64KB | 256MB | K26ARM | Supported from 2020.8. | +| ASUS \\ **RT‑AC56S**  |   |  ARM  |  800Mhz ×1  |  1GbE ×4  |  1 / 1  |  AC1200  |  128MB  |  64KB  |  128MB  |  K26ARM (SDK6.37)  | Use images ending with <typo bg: #002d38; fc: #819500; ff: monospace; fs: 14px; lh: 1.0; sp: nowrap; va: text-bottom;>…‑64K‑NOSMP.trx</typo>.  | 
-| Asus RT-AC1900U |   | ARM | 1000 | 2 | 1000 | 1 | 1 | AC1900 | 128MB | 64KB | 256MB | K26ARM | Supported from 2021.3. | +| ASUS \\ **RT‑AC56U/R**  |   |  ARM  |  800Mhz ×2  |  1GbE ×4  |  1 / 1  |  AC1200  |  128MB  |  64KB  |  256MB  |  K26ARM (SDK6.37)  |   | 
-| Asus RT-AC56S |   | ARM | 800 | 1 | 1000 | 1 | 1 | AC1200 | 128MB | 64KB | 128MB | K26ARM | Single core (please use images ending with "…-64K-NOSMP.trx"). | +| ASUS \\ **RT‑AC66U**  |  A1 / A2 / B1  |  MIPS R2  |  600Mhz ×1  |  1GbE ×4  |  2 / ‒  |  AC1750  |  32MB  |  64KB  |  256MB  |  K26RT-AC (SDK6.30)  | This model is distinguished from the RT-AC66U_B1 below as a MIPS-R2 device with two rear black USB 2.0 ports.  | 
-| Asus RT-AC56U/R |   | ARM | 800 | 2 | 1000 | 1 | 1 | AC1200 | 128MB | 64KB | 256MB | K26ARM |   | +| ASUS \\ **RT‑AC66U_B1**  |  B2 (others?)  |  ARM  |  1Ghz ×2  |  1GbE ×4  |  1 / 1  |  AC1750  |  128MB  |  64KB  |  256MB  |  K26ARM (SDK6.37)  | This model is distinguished from the RT-AC66U above as an ARM device with a blue USB 3.0 port in front and a black USB 2.0 port in back.  | 
-| Asus RT-AC66U | A1/A2/B1 | MIPS-R2 | 600 | 1 | 1000 | 2 | - | AC1750 | 32MB | 64KB | 256MB | K26RT-AC | This model is different from the RT-AC66U_B1, as this has two USB 2.0 ports at the rear of the router. | +| ASUS \\ **RT‑AC67U**  |   |  ARM  |  1Ghz ×2  |  1GbE ×4  |  1 / 1  |  AC1900  |  128MB  |  64KB  |  256MB  |  K26ARM (SDK6.37)  | Supported from 2020.8.  | 
-| Asus RT-AC66U_B1 |   | ARM | 1000 | 2 | 1000 | 1 | 1 | AC1750 | 128MB | 64KB | 256MB | K26ARM | Do not confuse this with the RT-AC66U Revision B1 above, which is a MIPS-R2 device. Check if the device has (blue) USB 3.x ports to be sure. Also, one USB port is at the front and the other one is at the rear. | +| ASUS \\ **RT‑AC68U/R/P/W**  |  A1 / A2 / B1  |  ARM  |  800Mhz ×2  |  1GbE ×4  |  1 / 1  |  AC1900  |  128MB  |  64KB  |  256MB  |  K26ARM (SDK6.37)  |   | 
-| Asus RT-AC67U |   | ARM | 1000 | 2 | 1000 | 1 | 1 | AC1900 | 128MB | 64KB | 256MB | K26ARM | Supported from 2020.8. | +| ASUS \\ **RT‑AC68U**  |  B2  |  ARM  |  1.4Ghz ×2  |  1GbE ×4  |  1 / 1  |  AC1900  |  128MB  |  64KB  |  256MB  |  K26ARM (SDK6.37)  |   | 
-| Asus RT-AC68U/R/P | A1/A2/B1 | ARM | 800 | 2 | 1000 | 1 | 1 | AC1900 | 128MB | 64KB | 256MB | K26ARM |   | +| ASUS \\ **RT‑AC68U**  |  C1 / E1 / V3  |  ARM  |  1Ghz ×2  |  1GbE ×4  |  1 / 1  |  AC1900  |  128MB  |  64KB  |  256MB  |  K26ARM (SDK6.37)  | C1 and E1 revs supported from 2019.3 then V3 rev support added in 2021.3. V4 rev **is NOT** supported.  | 
-| Asus RT-AC68U | C1/E1/V3 | ARM | 1000 | 2 | 1000 | 1 | 1 | AC1900 | 128MB | 64KB | 256MB | K26ARM | C1/E1 supported from 2019.3 \\ V3 supported from 2021.3 \\ V4 NOT supported | +| ASUS \\ **RT‑AC88U**  |   |  ARM  |  1.4Ghz ×2  |  1GbE ×8  |  1 / 1  |  AC3100  |  128MB  |  128KB  |  512MB  |  K26ARM714 (SDK714)  | Supported from 2022.6 ([[https://www.linksysinfo.org/index.php?threads/asus-rt-ac88u-preview-for-ft.77661/|forum thread]]) \\ \\ This image supports only ports LAN1–4 + WAN; the RTL8365MB switch (ports LAN5–8) are not supported. \\ \\ **With release 2024.4 and newer basic support for LAN Ports 5 to 8 has been added**  | 
-| Asus RT-AC68U | B2 | ARM | 1400 | 2 | 1000 | 1 | 1 | AC1900 | 128MB | 64KB | 256MB | K26ARM |   | +| ASUS \\ **RT‑AC1750**  |  B1  |  ARM  |  1Ghz ×2  |  1GbE ×4  |  1 / 1  |  AC1750  |  128MB  |  64KB  |  256MB  |  K26ARM (SDK6.37)  | Supported from 2021.3.  | 
-| Asus RT-AC1900P |   | ARM | 1400 | 2 | 1000 | 1 | 1 | AC1900 | 128MB | 64KB | 256MB | K26ARM |   | +| ASUS \\ **RT‑AC1900P**  |   |  ARM  |  1.4Ghz ×2  |  1GbE ×4  |  1 / 1  |  AC1900  |  128MB  |  64KB  |  256MB  |  K26ARM (SDK6.37)  |   | 
-| Asus RT-AC3200 |   | ARM | 1000 | 2 | 1000 | 1 | 1 | AC3200 | 128MB | 128KB | 256MB | K26ARM7 | Please check NVRAM first (64KB default at release or 128KB after Asus update). To get 128KB version FreshTomato flashed, you must first have Asus stock firmware V3.0.0.4.382.51374 installed. | +| ASUS \\ **RT‑AC1900U**  |   |  ARM  |  1Ghz ×2  |  1GbE ×4  |  1 / 1  |  AC1900  |  128MB  |  64KB  |  256MB  |  K26ARM (SDK6.37)  | Supported from 2021.3. \\  \\ Upgrade from AsusWRT to FreshTomato ([[firmware_basics_procedures|more details]])  | 
-| Asus RT-AC3100 |   | ARM | 1400 | 2 | 1000 | 1 | 1 | AC3100 | 128MB | 128KB | 512MB | K26ARM714 | Supported from 2022.6 \\ [[https://www.linksysinfo.org/index.php?threads/asus-rt-ac3100-preview-for-ft.77620/|for more info please see]] | +| ASUS \\ **RT‑AC3100**  |   |  ARM  |  1.4Ghz ×2  |  1GbE ×4  |  1 / 1  |  AC3100  |  128MB  |  128KB  |  512MB  |  K26ARM714 (SDK714)  | Supported from 2022.6 ([[https://www.linksysinfo.org/index.php?threads/asus-rt-ac3100-preview-for-ft.77620/|forum thread]])  | 
-| Asus RT-AC88U |   | ARM | 1400 | 2 | 1000 | 1 | 1 | AC3100 | 128MB | 128KB | 512MB | K26ARM714 | Supported from 2022.6 \\ [[https://www.linksysinfo.org/index.php?threads/asus-rt-ac88u-preview-for-ft.77661/|for more info please see]] \\ NOTE: This image will only support LAN Port 1 - 4 + WAN Port. The external RTL8365MB switch (LAN Port 5 - 8) will not be used/supported currently | +| ASUS \\ **RT‑AC3200**  |   |  ARM  |  1Ghz ×2  |  1GbE ×4  |  1 / 1  |  AC3200  |  128MB  |  128KB  |  256MB  |  K26ARM7 (SDK7)  | Please check NVRAM first (64KB default at release or 128KB after Asus update). \\ \\ To install 128KB FreshTomato version, you must be running Asus stock firmware v3.0.0.4.382.51374 or later.  | 
-| Asus RT-AC5300 |   | ARM | 1400 | 2 | 1000 | 1 | 1 | AC5300 | 128MB | 128KB | 512MB | K26ARM714 | Supported from 2022.6 \\ [[https://www.linksysinfo.org/index.php?threads/asus-rt-ac5300-preview-for-ft.77592/|for more info please see]] (NOT Asus GT-AC5300) | +| ASUS \\ **RT‑AC5300**  |   |  ARM  |  1.4Ghz ×2  |  1GbE ×4  |  1 / 1  |  AC5300  |  128MB  |  128KB  |  512MB  |  K26ARM714 (SDK714)  | Supported from 2022.6 ([[https://www.linksysinfo.org/index.php?threads/asus-rt-ac5300-preview-for-ft.77592/|forum thread]]) \\ \\ This is //NOT// the Asus **GT**‑AC5300.  | 
-| Asus WL-330gE |   | MIPS-R1 | 240 | 1 | 100 | - | - | G54 | 4MB | FIXME | 16MB | K26 |   | +| ASUS \\ **TUF‑AX3000**  |  V2  |  ARM  |  1.7Ghz ×4  |  1GbE ×4  |  ‒ / 1  |  AX3000  |  256MB  |  128KB  |  512MB  |  K419ARM (HND 5.04AX)  | Supported from 2023.3. \\ \\ Offers 2.5GbE WAN port, AsusWRT features/GUI //(based on GPL 388.22525)// + some FreshTomato features as of Sep. 2023.  | 
-| Asus WL-500GP | v1/v2 | MIPS-R1 | 240 | 1 | 100 | 2 | - | G54 | 8MB | FIXME | 32MB | K26 |   | +| ASUS \\ **WL‑330gE**  |   |  MIPS R1  |  240Mhz ×1  |  100MbE ×1  |  ‒ / ‒  |  G54  |  4MB  |  FIXME  |  16MB  |  K26 (SDK5.10)  |   | 
-| Asus WL-500W |   | MIPS-R1 | 264 | 1 | 100 | 2 | - | G54 | 8MB | FIXME | 32MB | K26 |   | +| ASUS \\ **WL‑500GP**  |  v1 / v2  |  MIPS R1  |  240Mhz ×1  |  100MbE ×4  |  2 / ‒  |  G54  |  8MB  |  32KB  |  32MB  |  K26 (SDK5.10)  |   | 
-| Asus WL-520GU |   | MIPS-R1 | 240 | 1 | 100 | 1 | - | G54 | 4MB | FIXME | 16MB | K26 |   | +| ASUS \\ **WL‑500W**  |   |  MIPS R1  |  264Mhz ×1  |  100MbE ×4  |  2 / ‒  |  G54  |  8MB  |  32KB  |  32MB  |  K26 (SDK5.10)  |   | 
-| Belkin F5D8235 | v3 | MIPS-R2 | 533 | 1 | 1000 | 1 | - | N300 | 8MB | 64KB | 64MB | K26 - K26RT-N | Only v3 is Broadcom - based  | +| ASUS \\ **WL‑520GU**  |   |  MIPS R1  |  240Mhz ×1  |  100MbE ×4  |  1 / ‒  |  G54  |  4MB  |  32KB  |  16MB  |  K26 (SDK5.10)  |   | 
-| Belkin F7D3301/7301 | v1 | MIPS-R2 | 453 | 1 | 100 | 2 | - | N300 | 8MB | 32KB | 64MB | K26 |   | +| Belkin \\ **F5D8235**  |  v3  |  MIPS R2  |  533Mhz ×1  |  1GbE ×4  |  1 / ‒  |  N300  |  8MB  |  64KB  |  64MB  |  K26 (SDK5.10) / K26RT-N (SDK5.110)  | Only v3 is Broadcom-based.  | 
-| Belkin F7D3302/7302 | v1 | MIPS-R2 | 453 | 1 | 100 | 1 | - | N300 | 8MB | 32KB | 64MB | K26 | Belkin F7D3302/7302. | +| Belkin \\ **F7D3301/7301**  |  v1  |  MIPS R2  |  453Mhz ×1  |  1GbE ×4  |  2 / ‒  |  N300  |  8MB  |  32KB  |  64MB  |  K26 (SDK5.10)  |   | 
-| Belkin F7D4302/F7D8302 | v1 | MIPS-R2 | 453 | 1 | 100 | 1 | - | A/N600 | 8MB | 32KB | 64MB | K26 - K26RT-N | Belkin Play Wireless | +| Belkin \\ **F7D3302/7302**  |  v1  |  MIPS R2  |  453Mhz ×1  |  100MbE ×4  |  1 / ‒  |  N300  |  8MB  |  32KB  |  64MB  |  K26 (SDK5.10)  |   | 
-| Belkin F9K1102 | v1/v3 | MIPS-R2 | 533 | 1 | 100 | 1 | - | N600 | 8MB | 32KB | 64MB | K26RT-N | [[https://www.linksysinfo.org/index.php?threads/belkin-f9k1102-tomato-bring-up.70850/post-327032|Support Information]] | +| Belkin \\ **F7D4302/8302**  |  v1  |  MIPS R2  |  453Mhz ×1  |  100MbE ×4  |  1 / ‒  |  N600  |  8MB  |  32KB  |  64MB  |  K26 (SDK5.10) / K26RT-N (SDK5.110)  | Belkin Play Wireless  | 
-| Belkin F9K1113 | v2 | ARM | 800 | 1 | 1000 | 1 | 1 | AC1200 | 16MB | 64KB | 128MB | K26ARM | Supported from 2021.1 \\ Additional cooling may be required. This router can get hot due to its design. [[https://www.linksysinfo.org/index.php?threads/belkin-f9k1113v2-firmware-testing.76214/|Thread]] \\ (wl0 is 5 GHz radio). | +| Belkin \\ **F9K1102**  |  v1 / v3  |  MIPS R2  |  533Mhz ×1  |  100MbE ×4  |  1 / ‒  |  N600  |  8MB  |  32KB  |  64MB  |  K26RT-N (SDK5.110)  | [[https://www.linksysinfo.org/index.php?threads/belkin-f9k1102-tomato-bring-up.70850/post-354779]]  | 
-| Buffalo WHR-G54S |   | MIPS-R1 | 200 | 1 | 100 | - | - | G54 | 4MB | 32KB | 16MB | K26 |   | +| Belkin \\ **F9K1113**  |  v2  |  ARM  |  800Mhz ×1  |  1GbE ×4  |  1 / 1  |  AC1200  |  16MB  |  64KB  |  128MB  |  K26ARM (SDK6.37)  | Supported from 2021.1. (wl0 is the 5 GHz radio) \\ \\ Additional cooling may be needed; this router can get hot due to its design. ([[https://www.linksysinfo.org/index.php?threads/belkin-f9k1113v2-firmware-testing.76214/|forum thread]])  | 
-| Buffalo WHR-G125 |   | MIPS-R1 | 240 | 1 | 100 | - | - | G108 | 4MB | 32KB | 16MB | K26 |   | +| Buffalo \\ **WHR‑G54S**  |   |  MIPS R1  |  200Mhz ×1  |  100MbE ×4  |  ‒ / ‒  |  G54  |  4MB  |  32KB  |  16MB  |  K26 (SDK5.10)  |   | 
-| Buffalo WHR-HP-G54 |   | MIPS-R1 | 200 | 1 | 100 | - | - | G54 | 4MB | 32KB | 16MB | K26 |   | +| Buffalo \\ **WHR‑G125**  |   |  MIPS R1  |  240Mhz ×1  |  100MbE ×4  |  ‒ / ‒  |  G108  |  4MB  |  32KB  |  16MB  |  K26 (SDK5.10)  |   | 
-| Buffalo WZR-D1800H |   | MIPS-R2 | 600 | 1 | 1000 | 1 | - | AC1750 | 128MB | 64KB | 128MB | K26RT-N |   | +| Buffalo \\ **WHR‑HP‑G54**  |   |  MIPS R1  |  200Mhz ×1  |  100MbE ×4  |  ‒ / ‒  |  G54  |  4MB  |  32KB  |  16MB  |  K26 (SDK5.10)  |   | 
-| Buffalo WZR-1750DHP |   | ARM | 800 | 2 | 1000 | 1 | 1 | AC1750 | 128MB | 64KB | 512MB | K26ARM | [[https://www.linksysinfo.org/index.php?threads/buffalo-wzr-1750dhp-bricked.74962/#post-333522|please read first]] | +| Buffalo \\ **WZR‑D1800H**  |   |  MIPS R2  |  600Mhz ×1  |  1GbE ×4  |  1 / ‒  |  AC1750  |  128MB  |  64KB  |  128MB  |  K26RT-N (SDK5.110)  |   | 
-| CD-R King CW-5358U |   | MIPS-R2 | FIXME | FIXME | 100 | 1 | - | N300 | 8MB | FIXME | 32MB | FIXME |   | +| Buffalo \\ **WZR‑1750DHP**  |   |  ARM  |  800Mhz ×2  |  1GbE ×4  |  1 / 1  |  AC1750  |  128MB  |  64KB  |  512MB  |  K26ARM (SDK6.37)  | [[https://www.linksysinfo.org/index.php?threads/buffalo-wzr-1750dhp-bricked.74962/#post-333522|Forum thread]]  | 
-| Cisco M10 v2 |   | FIXME | FIXME | FIXME | 100 | - | - | N300 | 4MB | 32KB | 32MB | K26RT-N |   | +| CD-R \\ **King CW‑5358U**  |   |  MIPS R2  |  300Mhz ×1  |  100MbE ×4  |  1 / ‒  |  N300  |  8MB  |  32KB  |  32MB  |  K26RT-N (SDK5.110)  |   | 
-| D-Link DIR-320 |   | MIPS-R1 | 240 | 1 | 100 | 1 | - | N150 | 4MB | FIXME | 32MB | K26 |   | +| Cisco \\ **M10**  |  v2  |  MIPS R2  |  300Mhz ×1  |  100MbE ×4  |  ‒ / ‒  |  N300  |  4MB  |  32KB  |  32MB  |  K26RT-N (SDK5.110)  |   | 
-| D-Link DIR-620 | C1 | MIPS-R2 | 530 | 1 | 100 | 1 | - | N300 | 8MB | FIXME | 64MB | K26RT-N |   | +| D-Link \\ **DIR‑320**  |   |  MIPS R1  |  240Mhz ×1  |  100MbE ×4  |  1 / ‒  |  N150  |  4MB  |  FIXME  |  32MB  |  K26 (SDK5.10)  |   | 
-| D-Link DIR-865L |   | MIPS-R2 | 600 | 1 | 1000 | 1 | - | AC1750 | 16MB | 32KB | 256MB | K26RT-AC | Supported from 2020.8. \\ NVRAM is limited to 32K. Use special build. | +| D-Link \\ **DIR‑620**  |  C1  |  MIPS R2  |  530Mhz ×1  |  100MbE ×4  |  1 / ‒  |  N300  |  8MB  |  FIXME  |  64MB  |  K26RT-N (SDK5.110)  |   | 
-| D-Link DIR-868L | A1/B1/C1 | ARM | 800 | 2 | 1000 | - | 1 | AC1750 | 128MB | 32KB | 128MB | K26ARM | NVRAM is limited to 32K. Use special build. | +| D-Link \\ **DIR‑865L**  |   |  MIPS R2  |  600Mhz ×1  |  1GbE ×4  |  1 / ‒  |  AC1750  |  16MB  |  32KB  |  256MB  |  K26RT-AC (SDK6.30)  | Supported from 2020.8. \\ \\ NVRAM is limited to 32K. Use special build.  | 
-| Fiboom HG320 |   | MIPS-R2 | 533 | 1 | 100 | 1 | - | FIXME | 16MB | 32KB | 256MB | K26RT-N |   | +| D-Link \\ **DIR‑868L**  |  A1 / B1 / C1  |  ARM  |  800Mhz ×2  |  1GbE ×4  |  ‒ / 1  |  AC1750  |  128MB  |  32KB  |  128MB  |  K26ARM (SDK6.37)  | NVRAM is limited to 32K. Use special build.  | 
-| Huawei WS880 |   | ARM | 800 | 2 | 1000 | - | 1 | AC1750 | 128MB | 64KB | 128MB | K26ARM |   | +| Fiboom \\ **HG320**  |   |  MIPS R2  |  533Mhz ×1  |  100MbE ×4  |  1 / ‒  |  FIXME  |  16MB  |  32KB  |  256MB  |  K26RT-N (SDK5.110)  |   | 
-| Linksys E800 |   | MIPS-R2 | 300 | 1 | 100 | - | - | N150 | 8MB | 64KB | 32MB | K26RT-N |   | +| Huawei \\ **WS880**  |   |  ARM  |  800Mhz ×2  |  1GbE ×4  |  ‒ / 1  |  AC1750  |  128MB  |  64KB  |  128MB  |  K26ARM (SDK6.37)  |   | 
-| Linksys E900 |   | MIPS-R2 | 300 | 1 | 100 | - | - | N300 | 8MB | 64KB | 32MB | K26RT-N |   | +| Linksys \\ **E800**  |   |  MIPS R2  |  300Mhz ×1  |  100MbE ×4  |  ‒ / ‒  |  N150  |  8MB  |  64KB  |  32MB  |  K26RT-N (SDK5.110)  |   | 
-| Linksys E1000 | v1/v2/v2.1 | MIPS-R2 | 300 | 1 | 100 | - | - | N300 | 4MB | 32KB | 32MB | K26RT-N |   | +| Linksys \\ **E900**  |   |  MIPS R2  |  300Mhz ×1  |  100MbE ×4  |  ‒ / ‒  |  N300  |  8MB  |  64KB  |  32MB  |  K26RT-N (SDK5.110)  |   | 
-| Linksys E1200 | v1 | MIPS-R2 | 300 | 1 | 100 | - | - | N300 | 4MB | 64KB | 32MB | K26RT-N |   | +| Linksys \\ **E1000**  |  v1 / v2 / v2.1  |  MIPS R2  |  300Mhz ×1  |  100MbE ×4  |  ‒ / ‒  |  N300  |  4MB  |  32KB  |  32MB  |  K26RT-N (SDK5.110)  |   | 
-| Linksys E1200 | v2 | MIPS-R2 | 300 | 1 | 100 | - | - | N300 | 8MB | 64KB | 32MB | K26RT-N |   | +| Linksys \\ **E1200**  |  v1  |  MIPS R2  |  300Mhz ×1  |  100MbE ×4  |  ‒ / ‒  |  N300  |  4MB  |  64KB  |  32MB  |  K26RT-N (SDK5.110)  |   | 
-| Linksys E1500 |   | MIPS-R2 | 300 | 1 | 100 | - | - | N300 | 8MB | 64KB | 32MB | K26RT-N |   | +| Linksys \\ **E1200**  |  v2  |  MIPS R2  |  300Mhz ×1  |  100MbE ×4  |  ‒ / ‒  |  N300  |  8MB  |  64KB  |  32MB  |  K26RT-N (SDK5.110)  |   | 
-| Linksys E1550 |   | MIPS-R2 | 300 | 1 | 100 | 1 | - | N300 | 16MB | 60KB | 64MB | K26RT-N |   | +| Linksys \\ **E1500**  |   |  MIPS R2  |  300Mhz ×1  |  100MbE ×4  |  ‒ / ‒  |  N300  |  8MB  |  64KB  |  32MB  |  K26RT-N (SDK5.110)  |   | 
-| Linksys E2000 |   | MIPS-R2 | 354 | 1 | 1000 | - | - | N300 | 8MB | 60KB | 32MB | K26 or K26RT-N |   | +| Linksys \\ **E1550**  |   |  MIPS R2  |  300Mhz ×1  |  100MbE ×4  |  1 / ‒  |  N300  |  16MB  |  60KB  |  64MB  |  K26RT-N (SDK5.110)  |   | 
-| Linksys E2500 | v1/v2 | MIPS-R2 | 300 | 1 | 100 | - | - | N600 | 8MB | 64KB | 64MB | K26RT-N | NVRAM is limited to 32kB. | +| Linksys \\ **E2000**  |   |  MIPS R2  |  354Mhz ×1  |  1GbE ×4  |  ‒ / ‒  |  N300  |  8MB  |  60KB  |  32MB  |  K26 (SDK5.10) / K26RT-N (SDK5.110)  |   | 
-| Linksys E2500 | v3 | MIPS-R2 | 500 | 1 | 100 | 1 | - | N600 | 16MB | 64KB | 64MB | K26RT-N | NVRAM is limited to 32kB. | +| Linksys \\ **E2500**  |  v1 / v2  |  MIPS R2  |  300Mhz ×1  |  100MbE ×4  |  ‒ / ‒  |  N600  |  8MB  |  64KB  |  64MB  |  K26RT-N (SDK5.110)  | NVRAM is limited to 32KB.  | 
-| Linksys E3000 |   | MIPS-R2 | 480 | 1 | 1000 | 1 | - | N600 | 8MB | 60KB | 64MB | K26 or K26RT-N |   | +| Linksys \\ **E2500**  |  v3  |  MIPS R2  |  500Mhz ×1  |  100MbE ×4  |  1 / ‒  |  N600  |  16MB  |  64KB  |  64MB  |  K26RT-N (SDK5.110)  | NVRAM is limited to 32KB.  | 
-| Linksys E3200 |   | MIPS-R2 | 500 | 1 | 1000 | 1 | - | N600 | 16MB | 64KB | 64MB | K26RT-N | 60K NVRAM. | +| Linksys \\ **E3000**  |   |  MIPS R2  |  480Mhz ×1  |  1GbE ×4  |  1 / ‒  |  N600  |  8MB  |  60KB  |  64MB  |  K26 (SDK5.10) / K26RT-N (SDK5.110)  |   | 
-| Linksys E4200 | v1 | MIPS-R2 | 480 | 1 | 1000 | 1 | - | N750 | 16MB | 60KB | 64MB | K26RT-N | v2 is not supported, due to its Marvell chipset. | +| Linksys \\ **E3200**  |   |  MIPS R2  |  500Mhz ×1  |  1GbE ×4  |  1 / ‒  |  N600  |  16MB  |  64KB  |  64MB  |  K26RT-N (SDK5.110)  | 60KB NVRAM.  | 
-| Linksys EA6200 | v1 | ARM | 800 | 1 | 1000 | - | 1 | AC900 | 128MB | 64KB | 128MB | K26ARM | CFE 32KB NVRAM Bug. \\ [[https://www.linksysinfo.org/index.php?threads/linksys-ea6200-ea6350v1-freshtomato-arm-discussion.74916|Please read the following before flashing]] \\ Single core (Use images ending with "…-64K-NOSMP.trx") \\ (wl0 is 5 GHz radio). | +| Linksys \\ **E4200**  |  v1  |  MIPS R2  |  480Mhz ×1  |  1GbE ×4  |  1 / ‒  |  N750  |  16MB  |  60KB  |  64MB  |  K26RT-N (SDK5.110)  | v2 is not supported (has a Marvell chipset).  | 
-| Linksys EA6300 | v1 | ARM | 800 | 2 | 1000 | - | 1 | AC1200 | 128MB | 64KB | 128MB | K26ARM | CFE 32KB NVRAM Bug. \\ [[https://www.linksysinfo.org/index.php?threads/guide-flash-linksys-ea6300v1-ea6400-ea6500v2-ea6700-ea6900v1-0-1-1-with-tomato.73877/|Please read the following before flashing]] | +| Linksys \\ **EA6200**  |  v1  |  ARM  |  800Mhz ×1  |  1GbE ×4  |  ‒ / 1  |  AC900  |  128MB  |  64KB  |  128MB  |  K26ARM (SDK6.37)  | CFE 32KB NVRAM bug; [[https://www.linksysinfo.org/index.php?threads/linksys-ea6200-ea6350v1-freshtomato-arm-discussion.74916|read this before flashing]]. \\ \\ Single core; use images ending in <typo bg: #002d38; fc: #819500; ff: monospace; fs: 14px; lh: 1.0; sp: nowrap; va: text-bottom;>…‑64K‑NOSMP.trx</typo>. \\ (wl0 is 5GHz radio)  | 
-| Linksys EA6350 | v1 | ARM | 800 | 1 | 1000 | - | 1 | AC1200 | 128MB | 64KB | 128MB | K26ARM | CFE 32KB NVRAM Bug. \\ [[https://www.linksysinfo.org/index.php?threads/linksys-ea6200-ea6350v1-freshtomato-arm-discussion.74916|Please read the following thread before flashing]] \\ Single core (please use the images ending with: "…-64K-NOSMP.trx") | +| Linksys \\ **EA6300**  |  v1  |  ARM  |  800Mhz ×2  |  1GbE ×4  |  ‒ / 1  |  AC1200  |  128MB  |  64KB  |  128MB  |  K26ARM (SDK6.37)  | CFE 32KB NVRAM bug; [[https://www.linksysinfo.org/index.php?threads/guide-flash-linksys-ea6300v1-ea6400-ea6500v2-ea6700-ea6900v1-0-1-1-with-tomato.73877/|read this before flashing]].  | 
-| Linksys EA6350 | v2 | ARM | 800 | 2 | 1000 | - | 1 | AC1200 | 128MB | 64KB | 128MB | K26ARM | Supported from 2022.1**.** More info [[https://www.linksysinfo.org/index.php?threads/full-support-linksys-ea6350v2-announcement.77202|here]] | +| Linksys \\ **EA6350**  |  v1  |  ARM  |  800Mhz ×1  |  1GbE ×4  |  ‒ / 1  |  AC1200  |  128MB  |  64KB  |  128MB  |  K26ARM (SDK6.37)  | CFE 32KB NVRAM bug; [[https://www.linksysinfo.org/index.php?threads/linksys-ea6200-ea6350v1-freshtomato-arm-discussion.74916|read this before flashing]]. \\ \\ Single core; use images ending in <typo bg: #002d38; fc: #819500; ff: monospace; fs: 14px; lh: 1.0; sp: nowrap; va: text-bottom;>…‑64K‑NOSMP.trx</typo>.  | 
-| Linksys EA6400 |   | ARM | 800 | 2 | 1000 | - | 1 | AC1200 | 128MB | 64KB | 128MB | K26ARM | CFE 32KB NVRAM Bug. \\ [[https://www.linksysinfo.org/index.php?threads/guide-flash-linksys-ea6300v1-ea6400-ea6500v2-ea6700-ea6900v1-0-1-1-with-tomato.73877/|Please read the following thread before flashing]] | +| Linksys \\ **EA6350**  |  v2  |  ARM  |  800Mhz ×2  |  1GbE ×4  |  ‒ / 1  |  AC1200  |  128MB  |  64KB  |  128MB  |  K26ARM (SDK6.37)  | Supported from 2022.1. ([[https://www.linksysinfo.org/index.php?threads/full-support-linksys-ea6350v2-announcement.77202|forum thread]])  | 
-| Linksys EA6500 | v2 | ARM | 800 | 2 | 1000 | 1 | 1 | AC1750 | 128MB | 64KB | 256MB | K26ARM | CFE 32KB NVRAM Bug. \\ [[https://www.linksysinfo.org/index.php?threads/guide-flash-linksys-ea6300v1-ea6400-ea6500v2-ea6700-ea6900v1-0-1-1-with-tomato.73877|Please read the following thread before flashing]] | +| Linksys \\ **EA6400**  |   |  ARM  |  800Mhz ×2  |  1GbE ×4  |  ‒ / 1  |  AC1200  |  128MB  |  64KB  |  128MB  |  K26ARM (SDK6.37)  | CFE 32KB NVRAM bug; [[https://www.linksysinfo.org/index.php?threads/guide-flash-linksys-ea6300v1-ea6400-ea6500v2-ea6700-ea6900v1-0-1-1-with-tomato.73877/|read this before flashing]].  | 
-| Linksys EA6700 |   | ARM | 800 | 2 | 1000 | 1 | 1 | AC1750 | 128MB | 64KB | 256MB | K26ARM | CFE 32KB NVRAM Bug. \\ [[https://www.linksysinfo.org/index.php?threads/guide-flash-linksys-ea6300v1-ea6400-ea6500v2-ea6700-ea6900v1-0-1-1-with-tomato.73877|Please read the following thread before flashing]] | +| Linksys \\ **EA6500**  |  v2  |  ARM  |  800Mhz ×2  |  1GbE ×4  |  1 / 1  |  AC1750  |  128MB  |  64KB  |  256MB  |  K26ARM (SDK6.37)  | CFE 32KB NVRAM bug; [[https://www.linksysinfo.org/index.php?threads/guide-flash-linksys-ea6300v1-ea6400-ea6500v2-ea6700-ea6900v1-0-1-1-with-tomato.73877|read this before flashing]].  | 
-| Linksys EA6900 | v1/v1.1 | ARM | 800 | 2 | 1000 | 1 | 1 | AC1900 | 128MB | 64KB | 256MB | K26ARM | CFE 32KB NVRAM Bug. \\ [[https://www.linksysinfo.org/index.php?threads/guide-flash-linksys-ea6300v1-ea6400-ea6500v2-ea6700-ea6900v1-0-1-1-with-tomato.73877/|Please read the following thread before flashing]] | +| Linksys \\ **EA6700**  |   |  ARM  |  800Mhz ×2  |  1GbE ×4  |  1 / 1  |  AC1750  |  128MB  |  64KB  |  256MB  |  K26ARM (SDK6.37)  | CFE 32KB NVRAM bug; [[https://www.linksysinfo.org/index.php?threads/guide-flash-linksys-ea6300v1-ea6400-ea6500v2-ea6700-ea6900v1-0-1-1-with-tomato.73877|read this before flashing]].  | 
-| Linksys WRT54GL | v1/v1.1 | MIPS-R1 | 200 | 1 | 100 | - | - | G54 | 4MB | 32KB | 16MB | K26 |   | +| Linksys \\ **EA6900**  |  v1 / v1.1  |  ARM  |  800Mhz ×2  |  1GbE ×4  |  1 / 1  |  AC1900  |  128MB  |  64KB  |  256MB  |  K26ARM (SDK6.37)  | CFE 32KB NVRAM bug; [[https://www.linksysinfo.org/index.php?threads/guide-flash-linksys-ea6300v1-ea6400-ea6500v2-ea6700-ea6900v1-0-1-1-with-tomato.73877/|read this before flashing]].  | 
-| Linksys WRT54G/GS | v2/v3/v4 | MIPS-R1 | 240 | 1 | 100 | - | - | G54 | 4-8MB | 32KB | 32-64MB | K26 |   | +| Linksys \\ **WRT54G/GS**  |  v2 / v3 / v4  |  MIPS R1  |  240Mhz ×1  |  100MbE ×4  |  ‒ / ‒  |  G54  |  4–8MB  |  32KB  |  32–64MB  |  K26 (SDK5.10)  |   | 
-| Linksys WRTSL54GS |   | MIPS-R1 | 266 | 1 | 100 | 1 | - | G54 | 8MB | 32KB | 32MB | K26 |   | +| Linksys \\ **WRT54GL**  |  v1 / v1.1  |  MIPS R1  |  200Mhz ×1  |  100MbE ×4  |  ‒ / ‒  |  G54  |  4MB  |  32KB  |  16MB  |  K26 (SDK5.10)  |   | 
-| Linksys WRT160N | v1 | MIPS-R1 | 266 | 1 | 100 | - | - | N300 | 4MB | 32KB | 32MB | K26 |   | +| Linksys \\ **WRTSL54GS**  |   |  MIPS R1  |  266Mhz ×1  |  100MbE ×4  |  1 / ‒  |  G54  |  8MB  |  32KB  |  32MB  |  K26 (SDK5.10)  |   | 
-| Linksys WRT160N | v3 | MIPS-R2 | 300 | 1 | 100 | - | - | N300 | 4MB | 32KB | 32MB | K26 |   | +| Linksys \\ **WRT160N**  |  v1  |  MIPS R1  |  266Mhz ×1  |  100MbE ×4  |  ‒ / ‒  |  N300  |  4MB  |  32KB  |  32MB  |  K26 (SDK5.10)  |   | 
-| Linksys WRT300N | v1 | MIPS-R1 | 264 | 1 | 100 | - | - | N300 | 4MB | 32KB | 32MB | K26 |   | +| Linksys \\ **WRT160N**  |  v3  |  MIPS R2  |  300Mhz ×1  |  100MbE ×4  |  ‒ / ‒  |  N300  |  4MB  |  32KB  |  32MB  |  K26 (SDK5.10)  |   | 
-| Linksys WRT310N | v2 | MIPS-R2 | 300 | 1 | 1000 | - | - | N300 | 4MB | 32KB | 32MB | K26 | Same as WRT160N v3 | +| Linksys \\ **WRT300N**  |  v1  |  MIPS R1  |  264Mhz ×1  |  100MbE ×4  |  ‒ / ‒  |  N300  |  4MB  |  32KB  |  32MB  |  K26 (SDK5.10)  |   | 
-| Linksys WRT320N |   | MIPS-R2 | 354 | 1 | 1000 | - | - | N300 | 8MB | 32KB | 32MB | K26 |   | +| Linksys \\ **WRT310N**  |  v2  |  MIPS R2  |  300Mhz ×1  |  1GbE ×4  |  ‒ / ‒  |  N300  |  4MB  |  32KB  |  32MB  |  K26 (SDK5.10)  | Same as the WRT160N v3.  | 
-| Linksys WRT610N | v2 | MIPS-R2 | 480 | 1 | 1000 | 1 | - | N300 | 8MB | 32KB | 64MB | K26 |   | +| Linksys \\ **WRT320N**  |   |  MIPS R2  |  354Mhz ×1  |  1GbE ×4  |  ‒ / ‒  |  N300  |  8MB  |  32KB  |  32MB  |  K26 (SDK5.10)  |   | 
-| Netgear AC1450 |   | ARM | 800 | 2 | 1000 | - | 1 | AC1750 | 128MB | 64KB | 256MB | K26ARM | Supported from 2022.3 \\ [[https://www.linksysinfo.org/index.php?threads/netgear-ac1450.77269/|Additional help here]] | +| Linksys \\ **WRT610N**  |  v2  |  MIPS R2  |  480Mhz ×1  |  1GbE ×4  |  1 / ‒  |  N300  |  8MB  |  32KB  |  64MB  |  K26 (SDK5.10)  |   | 
-| Netgear R6250 |   | ARM | 800 | 2 | 1000 | - | 1 | AC1600 | 128MB | 64KB | 256MB | K26ARM |   | +| Netgear \\ **AC1450**  |   |  ARM  |  800Mhz ×2  |  1GbE ×4  |  ‒ / 1  |  AC1750  |  128MB  |  64KB  |  256MB  |  K26ARM (SDK6.37)  | Supported from 2022.3. ([[https://www.linksysinfo.org/index.php?threads/netgear-ac1450.77269/|forum thread]])  | 
-| Netgear R6300 | v1 | MIPS-R2 | 600 | 1 | 1000 | 2 | 1 | AC1750 | 128MB | 64KB | 128MB | K26RT-AC |   | +| Netgear \\ **R6200**  |  v2  |  ARM  |  800Mhz ×1  |  1GbE ×4  |  ‒ / 1  |  AC1200  |  128MB  |  64KB  |  256MB  |  K26ARM (SDK6.37)  | Supported from 2023.5. ([[https://www.linksysinfo.org/index.php?threads/added-support-coming-soon-for-the-netgear-r6200v2-router.78246/|forum thread]])  | 
-| Netgear R6300 | v2 | ARM | 800 | 2 | 1000 | 1 | 1 | AC1750 | 128MB | 64KB | 256MB | K26ARM |   | +| Netgear \\ **R6250**  |   |  ARM  |  800Mhz ×2  |  1GbE ×4  |  ‒ / 1  |  AC1600  |  128MB  |  64KB  |  256MB  |  K26ARM (SDK6.37)  |   | 
-| Netgear R6400 | v1 | ARM | 800 | 2 | 1000 | 1 | 1 | AC1750 | 128MB | 128KB | 256MB | K26ARM |   | +| Netgear \\ **R6300**  |  v1  |  MIPS R2  |  600Mhz ×1  |  1GbE ×4  |  2 / 1  |  AC1750  |  128MB  |  64KB  |  128MB  |  K26RT-AC (SDK6.30)  |   | 
-| Netgear R6400 | v2 | ARM | 1000 | 2 | 1000 | 1 | 1 | AC1750 | 128MB | 128KB | 256MB | K26ARM |   | +| Netgear \\ **R6300**  |  v2  |  ARM  |  800Mhz ×2  |  1GbE ×4  |  1 / 1  |  AC1750  |  128MB  |  64KB  |  256MB  |  K26ARM (SDK6.37)  |   | 
-| Netgear R6700 | v1 | ARM | 1000 | 2 | 1000 | - | 1 | AC1750 | 128MB | 64KB | 256MB | K26ARM | Supported from 2020.8 \\ \\ Note: Do not enable JFFS with firmware ** less than 2022.1 for R6900, R7000 and R6700v1 (it will delete board_data partition!)** | +| Netgear \\ **R6400**  |  v1  |  ARM  |  800Mhz ×2  |  1GbE ×4  |  1 / 1  |  AC1750  |  128MB  |  128KB  |  256MB  |  K26ARM (SDK6.37)  |   | 
-| Netgear R6700 | v3 | ARM | 1000 | 2 | 1000 | 1 | 1 | AC1750 | 128MB | 128KB | 256MB (512MB) | K26ARM | Note: Some router can have 512 MB RAM. Images for both variants are provided:\\ "...-AIO-128K-512M.trx" (support for 512 MB RAM)\\ "...-AIO-128K.trx" (support up to 256 MB RAM)\\ Note 2: If not sure or unknown, just use the 512 MB RAM version, will work always | +| Netgear \\ **R6400**  |  v2  |  ARM  |  1Ghz ×2  |  1GbE ×4  |  1 / 1  |  AC1750  |  128MB  |  128KB  |  256MB  |  K26ARM (SDK6.37)  |   | 
-| Netgear R6900 | v1 | ARM | 1000 | 2 | 1000 | - | 1 | AC1900 | 128MB | 64KB | 256MB | K26ARM | Supported from 2021.3 \\ \\ Note: Do not enable JFFS with firmware ** less than 2022.1 for R6900, R7000 and R6700v1 (it will delete board_data partition!)** | +| Netgear \\ **R6700**  |  v1  |  ARM  |  1Ghz ×2  |  1GbE ×4  |  ‒ / 1  |  AC1750  |  128MB  |  64KB  |  256MB  |  K26ARM (SDK6.37)  | Supported from 2020.8. \\ \\ **Do not enable JFFS with FreshTomato prior to 2022.1; doing so deletes** <typo bg: #002d38; fc: #819500; ff: monospace; fs: 14px; lh: 1.0; sp: nowrap; va: text-bottom;>board_data</typo> **partition!**  | 
-| Netgear R7000 |   | ARM | 1000 | 2 | 1000 | 1 | 1 | AC1900 | 128MB | 64KB | 256MB | K26ARM | Note: Do not enable JFFS with firmware ** less than 2022.1 for R6900, R7000 and R6700v1 (it will delete board_data partition!)** \\ \\ Note 2: If you have a custom CFE like Vortex 1.3.0.7, please flash back your original Netgear cfe / bootloader before updating to Freshtomato 2020.3 and newer. | +| Netgear \\ **R6700**  |  v3  |  ARM  |  1Ghz ×2  |  1GbE ×4  |  1 / 1  |  AC1750  |  128MB  |  128KB  |  256MB or 512MB  |  K26ARM (SDK6.37)  | Some of these routers have 512MB RAM; images for both variants are provided, named: <typo bg: #002d38; fc: #819500; ff: monospace; fs: 14px; lh: 1.0; sp: nowrap; va: text-bottom;>…‑AIO‑128K‑512M.trx</typo> vs. <typo bg: #002d38; fc: #819500; ff: monospace; fs: 14px; lh: 1.0; sp: nowrap; va: text-bottom;>…‑AIO‑128K.trx</typo> (for ≤ 256MB RAM) \\ //If RAM size is unknown, use the 512MB RAM version; it will always work.//  | 
-| Netgear R7900 |   | ARM | 1000 | 2 | 1000 | - | 1 | AC3000 | 128MB | 64KB | 512MB (256 MB?) | K26ARM7 | Supported from 2022.4 | +| Netgear \\ **R6900**  |  v1  |  ARM  |  1Ghz ×2  |  1GbE ×4  |  ‒ / 1  |  AC1900  |  128MB  |  64KB  |  256MB  |  K26ARM (SDK6.37)  | Supported from 2021.3 \\ \\ **Do not enable JFFS with FreshTomato prior to 2022.1; doing so deletes** <typo bg: #002d38; fc: #819500; ff: monospace; fs: 14px; lh: 1.0; sp: nowrap; va: text-bottom;>board_data</typo> **partition!**  | 
-| Netgear R8000 |   | ARM | 1000 | 2 | 1000 | 1 | 1 | AC3200 | 128MB | 64KB | 256MB | K26ARM7 | Note: Do not enable JFFS with firmware ** less than 2022.3 for R8000 (it can delete/damage board_data partition!)** | +| Netgear \\ **R7000**  |   |  ARM  |  1Ghz ×2  |  1GbE ×4  |  1 / 1  |  AC1900  |  128MB  |  64KB  |  256MB  |  K26ARM (SDK6.37)  | **Do not enable JFFS with FreshTomato prior to 2022.1; doing so deletes** <typo bg: #002d38; fc: #819500; ff: monospace; fs: 14px; lh: 1.0; sp: nowrap; va: text-bottom;>board_data</typo> **partition!** \\ \\ //If you have a custom CFE/bootloader (e.g. Vortex 1.3.0.7), reinstall original Netgear CFE before flashing FreshTomato 2020.3 or newer.//  | 
-| Netgear XR300 |   | ARM | 1000 | 2 | 1000 | - | 1 | AC1750 | 128MB | 128KB | 512MB | K26ARM | Supported from 2021.1\\ (images ending with "…-128K-512M.trx") | +| Netgear \\ **EX7000**  |   |  ARM  |  800Mhz ×2  |  1GbE ×4  |  ‒ / 1  |  AC1900  |  16MB  |  64KB  |  128MB  |  K26ARM (SDK6.37)  | Work-in-progress; internal switch is not yet functional. \\ ([[https://www.linksysinfo.org/index.php?threads/add-support-for-netgear-ex7000.78502/|forum thread]])  | 
-| Netgear WNR2000 | v2 | MIPS-R2 | 300 | 1 | 100 | - | - | N300 | 4MB | 32KB | 32MB | K26 | Flash storage limited to about 3.5MB, so FT 2020.x IPv6 is the only current firmware that will fit. | +| Netgear \\ **R7900**  |   |  ARM  |  1Ghz ×2  |  1GbE ×4  |  ‒ / 1  |  AC3000  |  128MB  |  64KB  |  512MB or 256MB?  |  K26ARM7 (SDK7)  | Supported from 2022.4.  | 
-| Netgear WNR3500 | v2 | MIPS-R2 | 453 | 1 | 1000 | - | - | N300 | 3.5MB | 32KB | 32MB | K26 | Due to hard-coded jffs2 partition, flash size is reduced to only 3,473,408 bytes. As of today, FT 2020.x MiniIPV6 is 3,407,872 bytes and is the only image type that will fit. | +| Netgear \\ **R8000**  |   |  ARM  |  1Ghz ×2  |  1GbE ×4  |  1 / 1  |  AC3200  |  128MB  |  64KB  |  256MB  |  K26ARM7 (SDK7)  | **Do not enable JFFS with FreshTomato prior to 2022.3;  doing so deletes** <typo bg: #002d38; fc: #819500; ff: monospace; fs: 14px; lh: 1.0; sp: nowrap; va: text-bottom;>board_data</typo> **partition!**  | 
-| Netgear WNR3500L | v1 | MIPS-R2 | 453 | 1 | 1000 | 1 | - | N300 | 8MB | 32KB | 64MB | K26 |   | +| Netgear \\ **XR300**  |   |  ARM  |  1Ghz ×2  |  1GbE ×4  |  ‒ / 1  |  AC1750  |  128MB  |  128KB  |  512MB  |  K26ARM (SDK6.37)  | Supported from 2021.1, images end with <typo bg: #002d38; fc: #819500; ff: monospace; fs: 14px; lh: 1.0; sp: nowrap; va: text-bottom;>…-128K-512M.trx</typo>.  | 
-| Netgear WNR3500L | v2 | MIPS-R2 | 480 | 1 | 1000 | 1 | - | N300 | 32MB | 32KB | 128MB | K26RT-N | Please use only images with the name "freshtomato-Netgear-3500Lv2-K26USB_RT-N5x-XXXX.chk" (AIO or VPN version). | +| Netgear \\ **WNR2000**  |  v2  |  MIPS R2  |  300Mhz ×1  |  100MbE ×4  |  ‒ / ‒  |  N300  |  4MB  |  32KB  |  32MB  |  K26 (SDK5.10)  | Flash storage is ≲ 3.5MB; FreshTomato 2020.x IPv6 image is the only one that fits.  | 
-| Netgear WNDR3400 | v1 | MIPS-R2 | 480 | 1 | 100 | 1 | - | N600 | 8MB | 64KB | 64MB | K26RT-N |   | +| Netgear \\ **WNR3500**  |  v2  |  MIPS R2  |  453Mhz ×1  |  1GbE ×4  |  ‒ / ‒  |  N300  |  3.5MB  |  32KB  |  32MB  |  K26 (SDK5.10)  | Due to hard-coded JFFS2 partition, flash storage is ≲ 3,473KB; FreshTomato 2020.x MiniIPv6 image is the only one that fits.  | 
-| Netgear WNDR3400 | v2/v3 | MIPS-R2 | 530 | 1 | 100 | 1 | - | N600 | 8MB | 64KB | 64MB | K26RT-N | Important:Please Read <[[https://www.linksysinfo.org/index.php?threads/w-i-p-wndr3400v2-development.77559/post-337553|Flashing Instructions]]> | +| Netgear \\ **WNR3500L**  |  v1  |  MIPS R2  |  453Mhz ×1  |  1GbE ×4  |  1 / ‒  |  N300  |  8MB  |  32KB  |  64MB  |  K26 (SDK5.10)  | **Only enable JFFS on the FreshTomato Mini images, otherwise your** <typo bg: #002d38; fc: #819500; ff: monospace; fs: 14px; lh: 1.0; sp: nowrap; va: text-bottom;>board_data</typo> **partition is overwritten**. \\ \\ Images must be ≲ 7,475KB. ([[https://www.linksysinfo.org/index.php?threads/big-vpn-23-3-problem-on-wnr3500l.78067/#post-343373|forum thread]])  | 
-| Netgear WNDR3700 | v3 | MIPS-R2 | 480 | 1 | 1000 | 1 | - | N600 | 8MB | 64KB | 64MB | K26RT-N | Supported from 2020.6. | +| Netgear \\ **WNR3500L**  |  v2  |  MIPS R2  |  480Mhz ×1  |  1GbE ×4  |  1 / ‒  |  N300  |  32MB  |  32KB  |  128MB  |  K26RT-N (SDK5.110)  | Only install images with names ending in <typo bg: #002d38; fc: #819500; ff: monospace; fs: 14px; lh: 1.0; sp: nowrap; va: text-bottom;>…Netgear‑K26MIPSR2_RTN-USB-XXX</typo> (AIO or VPN).  | 
-| Netgear WNDR4000 |   | MIPS-R2 | 480 | 1 | 1000 | 1 |   | N750 | 8MB | 64KB | 64MB | K26RT-N | Supported from 2020.6. | +| Netgear \\ **WNDR3400**  |  v1  |  MIPS R2  |  480Mhz ×1  |  100MbE ×4  |  1 / ‒  |  N600  |  8MB  |  64KB  |  64MB  |  K26RT-N (SDK5.110)  |   | 
-| Netgear WNDR4500 | v1 | MIPS-R2 | 600 | 1 | 1000 | 2 | - | N900 | 128MB | 64KB | 128MB | K26RT-AC | At least up to 2022.2, the LEDs do not function. | +| Netgear \\ **WNDR3400**  |  v2 / v3  |  MIPS R2  |  530Mhz ×1  |  100MbE ×4  |  1 / ‒  |  N600  |  8MB  |  64KB  |  64MB  |  K26RT-N (SDK5.110)  | [[https://www.linksysinfo.org/index.php?threads/w-i-p-wndr3400v2-development.77559/post-337553|Forum thread]]  | 
-| Netgear WNDR4500 | v2 | MIPS-R2 | 600 | 1 | 1000 | 2 | - | N900 | 128MB | 64KB | 128MB | K26RT-AC |   | +| Netgear \\ **WNDR3700**  |  v3  |  MIPS R2  |  480Mhz ×1  |  1GbE ×4  |  1 / ‒  |  N600  |  8MB  |  64KB  |  64MB  |  K26RT-N (SDK5.110)  | Supported from 2020.6.  | 
-| Ovislink WL1600GL |   | MIPS-R1 | 240 | 1 | 100 | - | - | G125 | 4MB | FIXME | 16MB | K26 |   | +| Netgear \\ **WNDR4000**  |   |  MIPS R2  |  480Mhz ×1  |  1GbE ×4  |  1 / ‒  |  N750  |  8MB  |  64KB  |  64MB  |  K26RT-N (SDK5.110)  | Supported from 2020.6.  | 
-| Tenda AC15 | v1.0 | ARM | 800 | 2 | 1000 | - | 1 | AC1900 | 16MB | 64KB | 256MB | K26ARM |   | +| Netgear \\ **WNDR4500**  |  v1  |  MIPS R2  |  600Mhz ×1  |  1GbE ×4  |  2 / ‒  |  N900  |  128MB  |  64KB  |  128MB  |  K26RT-AC (SDK6.30)  | Prior to FreshTomato 2022.3, the LEDs do not function.  | 
-| Tenda AC18 | v1.0 | ARM | 800 | 2 | 1000 | - | 1 | AC1900 | 128MB | 64KB | 256MB | K26ARM |   | +| Netgear \\ **WNDR4500**  |  v2  |  MIPS R2  |  600Mhz ×1  |  1GbE ×4  |  2 / ‒  |  N900  |  128MB  |  64KB  |  128MB  |  K26RT-AC (SDK6.30)  |   | 
-| Tenda N6 |   | MIPS-R2 | 300 | 1 | 100 | - | - | N600 | 8MB | FIXME | 64MB | K26RT-N |   | +| Ovislink \\ **WL1600GL**  |   |  MIPS R1  |  240Mhz ×1  |  100MbE ×4  |  ‒ / ‒  |  G125  |  4MB  |  FIXME  |  16MB  |  K26 (SDK5.10)  |   | 
-| Tenda N60 |   | MIPS-R2 | 500 | 1 | 1000 | 1 | - | N600 | 8MB | FIXME | 64MB | K26RT-N |   | +| Tenda \\ **AC15**  |  v1.0  |  ARM  |  800Mhz ×2  |  1GbE ×3  |  ‒ / 1  |  AC1900  |  16MB  |  64KB  |  128MB  |  K26ARM (SDK6.37)  |   | 
-| Tenda N80 |   | MIPS-R2 | 500 | 1 | 1000 | 1 | - | N900 | 8MB | FIXME | 128MB | K26RT-N |   | +| Tenda \\ **AC18**  |  v1.0  |  ARM  |  800Mhz ×2  |  1GbE ×4  |  ‒ / 1  |  AC1900  |  128MB  |  64KB  |  256MB  |  K26ARM (SDK6.37)  |   | 
-| Tenda W1800R |   | MIPS-R2 | 600 | 1 | 1000 | 2 | - | AC1750 | 16MB | FIXME | 256MB | K26RT-AC |   | +| Tenda \\ **N6**  |   |  MIPS R2  |  300Mhz ×1  |  100MbE ×4  |  ‒ / ‒  |  N600  |  8MB  |  32KB  |  64MB  |  K26RT-N (SDK5.110)  |   | 
-| Xiaomi Mi R1D |   | ARM | 1000 | 2 | 1000 | 1 | - | AC1200 | 128MB | 64KB | 256MB | K26ARM | **IMPORTANT :** This unit may be  bricked if you attempt to FULLY erase NVRAM. Resetting values to defaults works safely. To access the CFE when you have the stock xVortex CFE, you must power on the unit while holding the Reset button for 10 seconds. [[https://forum.dd-wrt.com/phpBB2/viewtopic.php?p=1139833#1139833|Details]] \\   \\ Please use the images with ending "…-Custom-64K.trx"\\ \\ (wl0 is the 5 GHz radio). | +| Tenda \\ **N60**  |   |  MIPS R2  |  500Mhz ×1  |  1GbE ×4  |  1 / ‒  |  N600  |  8MB  |  32KB  |  64MB  |  K26RT-N (SDK5.110)  |   | 
-| ZTE ZXV10 H618B |   | MIPS-R1 | 240 | 1 | 100 | 1 | - | G54 | 16MB | FIXME | 32MB | K26 |   | +| Tenda \\ **N80**  |   |  MIPS R2  |  500Mhz ×1  |  1GbE ×4  |  1 / ‒  |  N900  |  8MB  |  64KB  |  128MB  |  K26RT-N (SDK5.110)  |   | 
-| ZTE H218N |   | MIPS-R2 | 500 | 1 | 1000 | 1 | - | N300 | 16MB | FIXME | 64MB | K26RT-N |   |+| Tenda \\ **W1800R**  |   |  MIPS R2  |  600Mhz ×1  |  1GbE ×4  |  2 / ‒  |  AC1750  |  16MB  |  64KB  |  256MB  |  K26RT-AC (SDK6.30)  |   | 
 +| Xiaomi \\ **MiWiFi R1D**  |   |  ARM  |  1Ghz ×2  |  1GbE ×2  |  1 / ‒  |  AC1200  |  128MB  |  64KB  |  256MB  |  K26ARM (SDK6.37)  | This unit may be **bricked** if you try to FULLY erase NVRAM; but resetting values to defaults is safe. \\ \\ To access the CFE when you have stock xVortex CFE, power on while holding Reset button for 10 seconds. ([[https://forum.dd-wrt.com/phpBB2/viewtopic.php?p=1139833#1139833|forum thread]]) \\ \\ Use images whose name ends in <typo bg: #002d38; fc: #819500; ff: monospace; fs: 14px; lh: 1.0; sp: nowrap; va: text-bottom;>…‑Custom‑64K.trx</typo> \\ (wl0 is the 5GHz radio)  | 
 +| ZTE \\ **ZXV10 H618B**  |   |  MIPS R1  |  240Mhz ×1  |  100MbE ×4  |  1 / ‒  |  G54  |  16MB  |  FIXME  |  32MB  |  K26 (SDK5.10)  |   | 
 +| ZTE \\ **H218N**  |   |  MIPS R2  |  500Mhz ×1  |  100MbE ×4  |  1 / ‒  |  N300  |  16MB  |  FIXME  |  64MB  |  K26RT-N (SDK5.110)  |   |
  
 </sortable> </sortable>
  
  
hardware_compatibility.1673050260.txt.gz · Last modified: 2023/01/07 00:11 by txnative

Page Tools

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki