This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionLast revisionBoth sides next revision | ||
nas-bittorrent [2022/02/22 15:07] – rs232 | nas-bittorrent [2023/06/04 18:04] – -condense, formatting hogwild | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ===== Bittorrent | + | ====== BitTorrent |
- | You will find this feature in builds | + | This feature |
- | {{: | + | \\ |
- | ** Enable**: Kicks off the process at every boot, plus runs it as soon as you select Save.\\ | + | |
- | {{: | + | {{: |
- | **Transmission binary path**: Internal/ | + | |
- | {{: | + | \\ |
- | **Click here to open Transmission GUI**: As the name suggests it will open the Transmission administration GUI in a new browser' | + | |
- | **Keepalive**: | + | |
- | **Check alive every**: The frequency at which the above control should be performed.\\ | + | |
- | **Delay at startup**: For different reasons, but possibly waiting for external storage to be fully up and running, defining a time here in seconds would, as the name suggests, delay the kick off of the process at boot time.\\ | + | |
- | **Listening port**: Define here the port linked to the process. This will be both TCP and UDP.\\ | + | |
- | **Downloading directory**: | + | |
- | **Use incomplete/ | + | |
- | **Autoadd .torrents**: | + | |
- | {{: | + | **Enable:** |
- | **Enable | + | |
- | **Listening GUI port**: Define the port where the Transmission | + | |
- | **Authentication required**: It disables anonymous access (strongly suggested) and uses the credentials defined in the below two fields.\\ | + | |
- | **Username**: | + | |
- | **Password**: | + | |
- | **Allow remote access**: If enabled the Listening port becomes reachable also on the WAN side.\\ | + | |
- | {{: | + | {{: |
- | **Limits**: The next paragraph " | + | |
- | {{: | + | \\ **Transmission binary path:** This specifies where the Transmission binary will be found on the filesystem. |
- | **Download queuing**: Is yet another form of limit and controls how many concurrents active Downloads can run simultaneously.\\ | + | |
- | **Upload queuing**: Same as the option above but applies to Uploads instead.\\ | + | |
- | {{: | + | * Internal |
- | **Find more peers using**: Defines on what torrent network type/protocols your Transmission | + | * Optware - Choosing this makes FreshTomato use an Optware/Entware installation of Transmission. |
+ | * Custom - Choosing this lets you specify a custom path to the location of the binary.\\ | ||
- | {{: | + | \\ |
- | **Message level**: None(0)/Error(3)/Info(6)/Debug(7) - Defines the highest Transmission loglevel messaged to be captured | + | |
+ | **Click here to open Transmission GUI: | ||
+ | |||
+ | **Keepalive: | ||
+ | |||
+ | * **Check alive every: | ||
+ | |||
+ | \\ \\ {{: | ||
+ | |||
+ | **Listening port: | ||
+ | |||
+ | **Downloading directory: | ||
+ | |||
+ | **Use incomplete/: | ||
+ | |||
+ | **Autoadd .torrents: | ||
+ | |||
+ | ===== Remote Access ===== | ||
+ | |||
+ | {{: | ||
+ | |||
+ | **Enable GUI: | ||
+ | |||
+ | * **Listening GUI port: | ||
+ | |||
+ | **Authentication required: | ||
+ | |||
+ | * Username - This specifies your administration username. | ||
+ | * Password - This specifies your administration password. | ||
+ | |||
+ | **Allow remote access: | ||
+ | |||
+ | ===== Limits ===== | ||
+ | |||
+ | The Limits section has settings to define Transmission' | ||
+ | |||
+ | \\ | ||
+ | |||
+ | {{: | ||
+ | |||
+ | ===== Queue torrents ===== | ||
+ | |||
+ | {{: | ||
+ | |||
+ | **Upload queuing: | ||
+ | |||
+ | ===== Advanced Settings | ||
+ | |||
+ | {{: | ||
+ | |||
+ | **Find more peers using: | ||
+ | |||
+ | {{: | ||
+ | |||
+ | **Message level:** This setting defines the lowest level of Transmission messages to be captured in the system logs | ||
+ | |||
+ | * None (0) - No Transmission messages will be stored in system logs. | ||
+ | * Error (3) - Only error levels and above will be stored in system logs. | ||
+ | * Info (6) - Only Information messages and above will be stored in system logs | ||
+ | * Debug (7) - Debugging level messages and higher will be stored | ||
+ | |||
+ | \\ | ||
+ | |||
+ | {{: | ||
+ | |||
+ | **Save settings location: | ||
+ | |||
+ | * Download directory - | ||
+ | * JFFS - | ||
+ | * CIFS1 - | ||
+ | * RAM - | ||
+ | |||
+ | Custom - \\ | ||
+ | |||
+ | \\ | ||
+ | |||
+ | {{: | ||
+ | |||
+ | **Blocklist**: | ||
+ | |||
+ | An alternative method to define the single list here is to use P2Partisan instead. Using P2Partisan, more lists can be defined. However, to use P2Partisan, a manual script installation is required. | ||
+ | |||
+ | **Custom Log File Path**: | ||
+ | |||
+ | **Custom Configuration**: | ||
- | {{: | ||
- | **Save settings location**: Download directory/ | ||
- | {{: | ||
- | **Blocklist**: | ||
- | **Custom Log File Path**: Define here the location where you want Transmission to log its activity.\\ | ||
- | **Custom Configuration**: |