This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
status-devices [2023/05/05 23:37] – -condense hogwild | status-devices [2024/03/02 21:58] – -correct inaccuracies in wireless hardware section hogwild | ||
---|---|---|---|
Line 5: | Line 5: | ||
\\ {{: | \\ {{: | ||
- | \\ **Interface** | + | \\ **Interface:** |
* '' | * '' | ||
Line 15: | Line 15: | ||
* '' | * '' | ||
* If you have Virtual Wireless set up, you'll probably have several of these. | * If you have Virtual Wireless set up, you'll probably have several of these. | ||
- | * The , depending | + | * This will depend |
* Virtual wireless interfaces will also appear here. | * Virtual wireless interfaces will also appear here. | ||
- | * Main Wireless | + | * Main wireless |
* Virtual wireless interfaces are named as wlX.X . | * Virtual wireless interfaces are named as wlX.X . | ||
Line 24: | Line 24: | ||
In FreshTomato, | In FreshTomato, | ||
- | \\ **Media**: In this column, an icon represents the interface on which the device is connected and its connection status. Interface types include: | + | \\ **Media:** An icon in this column represents the interface on which the device is connected, and its connection status. |
+ | |||
+ | Interface types include: | ||
* Ethernet | * Ethernet | ||
Line 35: | Line 37: | ||
* PPTP client | * PPTP client | ||
- | WAN interfaces are represented | + | \\ |
+ | |||
+ | WAN interfaces are shown with black and white inverted. A greyed-out power icon represents a device that is disconnected or off. | ||
- | \\ **MAC Address** is the physical (hardware) address associated with the interface. | + | \\ **MAC Address: **This is the physical (hardware) address associated with the interface. |
* Clicking on the MAC address opens a search to identify the hardware vendor, based on the device' | * Clicking on the MAC address opens a search to identify the hardware vendor, based on the device' | ||
Line 45: | Line 49: | ||
* [DR] stands for //DHCP Reservation. // | * [DR] stands for //DHCP Reservation. // | ||
- | * This forwards you to to the [[: | + | * This forwards you to the [[: |
- | * From there, checking the Bound to option will enable static ARP mapping to the MAC address to protect against [[https:// | + | * From there, checking the //Bound to// option will enable static ARP mapping to the MAC address. |
+ | * This helps to protect against [[https:// | ||
- | * [BWL] forwards you to the [[: | + | * [BWL] forwards you to the [[bwlimit|Bandwidth Limiter]] menu for that device. |
* There, you can limit the bandwidth of the device associated with this MAC address. | * There, you can limit the bandwidth of the device associated with this MAC address. | ||
Line 55: | Line 60: | ||
* [WLF] forwards you to the [[: | * [WLF] forwards you to the [[: | ||
- | \\ **IP Address** displays the IP address linked to the MAC address | + | \\ **IP Address:** |
- | **Name** shows the DHCP Hostname of the client device. If no name is shown, it is usually because the device got its lease on the network from a different router, or this router was rebooted after the lease was given. You can work around this by adding your own dhcp-host reference in the dnsmasq Custom configuration. | + | **Name:** This shows the DHCP Hostname of the client device. If no name is shown, it' |
For example, '' | For example, '' | ||
- | Note that this field is also affected by the "// | + | This field is also affected by the "// |
- | **RSSI** indicates Relative Signal Strength. | + | **RSSI:** |
- | **Quality** is similar to RSSI but considers other parameters, | + | **Quality: **This is similar to RSSI, but considers other parameters, |
- | **TX/RX Rate** is the current transmit/ | + | **TX/RX Rate: **This is the current transmit/ |
- | **Lease** displays the time remaining before | + | **Lease: **This displays the time remaining before |
\\ | \\ | ||
Line 77: | Line 82: | ||
\\ | \\ | ||
- | **Noise floor** indicates the amount of interference affecting each physical radio interface. Noise, like RSSI, is measured in negative numbers. The best possible value is -100dBm. Any interference will increase the noise value and decrease the Quality. | + | **Noise floor: **This indicates the amount of interference affecting each physical radio interface. Noise, like RSSI, is measured in negative numbers. The best possible value is -100dBm. Any interference will increase the noise value and decrease the Quality. |
- | If you experience a strong RSSI //and// a strong Noise floor, the WiFi is likely to be unusable. In such situations, the main issue is usually other routers or Access Points transmitting on the same channel. Use the [[: | + | If you experience a strong RSSI //and// a strong Noise floor, the WiFi is likely to be unusable. In these situations, the main cause is usually other routers or Access Points transmitting on the same channel. Use the [[tools-survey|Wireless Survey]] |
- | On the 2.4GHz band, common sources of interference include Bluetooth devices, cordless | + | On the 2.4GHz band, common sources of interference include: |
+ | |||
+ | * Bluetooth devices | ||
+ | * Cordless | ||
+ | * Wireless | ||
+ | * Low-quality power supplies | ||
+ | * Microwave | ||
+ | |||
+ | \\ | ||
+ | |||
+ | Typically, there are fewer sources of interference | ||
\\ | \\ | ||
Line 87: | Line 102: | ||
{{: | {{: | ||
- | **Measure**: | + | **Measure**: |
- | **Network Discovery**: | + | **Network Discovery**: |
- | To the right of the Network Discovery mode is a non-adjustable countdown timer which represents how often the script is run. Essentially, | + | Network Discovery can be set to use the Linux **arping** command or the **traceroute** command. Arping is the preferred setting, as it's faster and lighter on resources. However, sometimes, traceroute may perform network discovery more precisely. This is true with Apple devices. |
+ | |||
+ | To the right of the Network Discovery mode is a non-adjustable countdown timer which represents how often the script is run. Essentially, | ||
\\ | \\ | ||
- | {{: | + | {{: |
+ | |||
+ | \\ | ||
\\ | \\ | ||