This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
status-devices [2024/05/07 02:17] – -format-remove one space before bullets hogwild | status-devices [2024/05/07 02:35] – -format-remove extra space before bullets hogwild | ||
---|---|---|---|
Line 10: | Line 10: | ||
*'' | *'' | ||
*This name might be used directly. | *This name might be used directly. | ||
- | *The name may be used indirectly if a bridge, PPP, or VPN connection is associated with the interface. | + | *The name may be used indirectly if a bridge/PPP/VPN connection is associated with the interface. |
*'' | *'' | ||
*For example, in the example above, vlan2 represents the WAN interface. | *For example, in the example above, vlan2 represents the WAN interface. | ||
Line 21: | Line 21: | ||
\\ | \\ | ||
- | WiFi-connected devices | + | WiFi-connected devices appear under the interface name of the SSID to which they are connected . |
- | Device names start at " | + | Device names start at " |
- | Additional instances are created when virtual interfaces are created (secondary SSIDs). | + | When virtual interfaces are created (secondary SSIDs), additional instances are created. |
- | \\ **Media: | + | \\ **Media: |
Interface types include: | Interface types include: | ||
Line 48: | Line 48: | ||
\\ **MAC Address: **is the hardware address associated with the interface. | \\ **MAC Address: **is the hardware address associated with the interface. | ||
- | * Clicking the MAC address opens a search to identify hardware vendor, based on the device OUI ([[https:// | + | *Clicking the MAC address opens a search to identify hardware vendor, |
- | * The OUI is derived from the first 6 digits of its MAC address. | + | *The OUI is derived from the first 6 digits of its MAC address. |
- | * This function is useful only for factory-programmed MAC addresses. | + | *This function is useful only for factory-programmed MAC addresses. |
- | * It will not work with manually-configured MAC addresses, | + | *It won' |
- | * [DR] stands for //DHCP Reservation.// | + | *[DR] stands for //DHCP Reservation.// |
- | * This forwards you to the [[: | + | *This forwards you to the [[: |
- | * From there, checking the //Bound to// option will enable static ARP mapping to the MAC address. | + | *While there, checking the //Bound to// option will enable static ARP mapping |
- | * This helps to protect against [[https:// | + | *This helps to protect against [[https:// |
- | * [BWL] forwards you to the [[bwlimit|Bandwidth Limiter]] menu for that device. | + | *[BWL] forwards you to the [[bwlimit|Bandwidth Limiter]] menu for that device. |
- | * There, you can limit the bandwidth of the device associated with this MAC address. | + | * Here, you can limit the bandwidth of the device associated with this MAC address. |
- | * [AR] forwards you to the [[: | + | *[AR] forwards you to the [[: |
- | * [WLF] forwards you to the [[: | + | *[WLF] forwards you to the [[: |
\\ **IP Address: | \\ **IP Address: | ||
- | If no address is shown, | + | If no address is shown, |
- | **Name: | + | **Name:** shows the DHCP Hostname of the client device. If no name is shown, it's usually because the device got its lease from a different router, or this router was rebooted after the lease was given. |
For example, '' | For example, '' | ||
Line 75: | Line 75: | ||
This field is also affected by the "// | This field is also affected by the "// | ||
- | **RSSI: | + | **RSSI: |
RSSI is measured in negative numbers, where 0 is the best possible value. Thus, -53 is a stronger signal than -74. | RSSI is measured in negative numbers, where 0 is the best possible value. Thus, -53 is a stronger signal than -74. | ||
- | **Quality: **This is similar to RSSI, but considers | + | **Quality: **is similar to RSSI, but also considers parameters like noise floor/interference. Quality is a more accurate |
- | **TX/RX Rate: **This is the current transmit/ | + | **TX/RX Rate: **This is the current transmit/ |
- | **Lease: **This displays the time remaining | + | **Lease: **displays the time remaining |
\\ | \\ | ||
Line 91: | Line 91: | ||
\\ | \\ | ||
- | **Noise floor: **This indicates the amount of interference affecting each physical radio interface. | + | **Noise floor: **indicates the amount of interference affecting each physical radio interface. |
Noise, like RSSI, is measured in negative numbers. The best possible value is -100dBm. Any interference will increase the noise value and decrease the Quality. | Noise, like RSSI, is measured in negative numbers. The best possible value is -100dBm. Any interference will increase the noise value and decrease the Quality. | ||
- | If you experience a strong RSSI //and// a strong Noise floor, | + | If you experience a strong RSSI //and// a strong Noise floor, WiFi is likely to be unusable. In these situations, the main cause is usually other WiFi gear transmitting on the same channel. Use the [[tools-survey|Wireless Survey]] tool to get more information. |
On the 2.4GHz band, common sources of interference include: | On the 2.4GHz band, common sources of interference include: | ||
- | * Bluetooth devices | + | *Bluetooth devices |
- | * Cordless phones | + | *Cordless phones |
- | * Wireless headphones | + | *Wireless headphones |
- | * Low-quality power supplies | + | *Low-quality power supplies |
- | * Microwave ovens | + | *Microwave ovens |
\\ | \\ | ||
- | Typically, there is les interference on the 5GHz band. One source of interference is DFS (Dynamic Frequency Selection) only for certain channels | + | Typically, there is less interference on the 5GHz band. One source of interference is DFS (Dynamic Frequency Selection) only for certain channels. DFS is a WiFi function that lets 5GHz WiFi use frequencies |
\\ | \\ | ||
Line 113: | Line 113: | ||
{{: | {{: | ||
- | **Measure**: | + | **Measure**: |
- | **Network Discovery**: | + | **Network Discovery**: |
- | Network Discovery can be set to use the Linux **arping** command or the **traceroute** command. Arping is the preferred | + | Network Discovery can be set to use Linux' |
- | To the right of the Network Discovery mode is a non-adjustable countdown timer which represents | + | To the right of Network Discovery mode is a non-adjustable countdown timer representing |
\\ | \\ |