This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
status-overview [2023/05/26 17:32] – [Ethernet Ports State] -formatting hogwild | status-overview [2023/06/08 15:46] – [Wireless (2.4 GHz / ethx) and Wireless (5 GHz/ethy)] hogwild | ||
---|---|---|---|
Line 15: | Line 15: | ||
\\ NOTE: The blinking LED colour matches the link speed. However, the LEDs flashing interval is fixed;\\ it doesn' | \\ NOTE: The blinking LED colour matches the link speed. However, the LEDs flashing interval is fixed;\\ it doesn' | ||
- | \\ | + | |
- | + | ||
- | Settings for the Ethernet Ports State are in the [[:network|Network]] menu. | + | |
\\ | \\ | ||
Line 26: | Line 24: | ||
Here you can find the WAN status. Information displayed here will vary based on the type of WAN connectivity (DHCP, PPPoE, etcetera). | Here you can find the WAN status. Information displayed here will vary based on the type of WAN connectivity (DHCP, PPPoE, etcetera). | ||
- | **CPU Load: **This is the proportion of time (in percent) the CPU is in use for running tasks/ | + | **CPU Load: **This is the proportion of time (in percent) the CPU is in use for running tasks/ |
CPU Load is in the System section. | CPU Load is in the System section. | ||
)) | )) | ||
- | **Status: **This indicates whether the router is connected to or disconnected from the Internet. | + | **Status: |
- | **Connection Uptime: **This displays the amount of time the router has been connected to the Internet during its current session. | + | **Connection Uptime: |
- | **Remaining Lease Time:** This shows the amount of time left on the WAN port's current DHCP/IP lease. | + | **Remaining Lease Time: |
- | **Release**: | + | **Release**: |
+ | |||
+ | **Renew: | ||
- | **Renew: **Clicking this button attempts to renew the IP lease, and reconnect the router to the Internet/ | ||
===== LAN ===== | ===== LAN ===== | ||
Line 46: | Line 45: | ||
===== Wireless (2.4 GHz / ethx) and Wireless (5 GHz/ethy) ===== | ===== Wireless (2.4 GHz / ethx) and Wireless (5 GHz/ethy) ===== | ||
- | The Wireless (2.4 GHz /ethx) and Wireless (5 GHz/ethy) section displays (model-dependent) information and status of the 2.4 GHz Wi-Fi interface | + | The Wireless (2.4 GHz /ethx) and Wireless (5 GHz/ethy) section displays (model-dependent) information and status of the corresponding router |
- | The FreshTomato device name may be different than what's shown, depending on your hardware. | + | The FreshTomato device name may be different than what's shown, depending on your hardware. FreshTomato device name numbers begin at 0. For example, the first Wi-Fi interface might be eth0, while the second might be eth1. |
\\ [[https:// | \\ [[https:// | ||
- | \\ **Enable:** Clicking this button will turn on the Wi-Fi radio shown under the same heading. This button only appears on some hardware. | + | \\ **Enable: |
- | **Disable: | + | **Disable: |
- | **Stop:** Clicking | + | **Stop: |
+ | |||
+ | Selecting any interval rate from the dropdown menu then clicking **Refresh** will begin displaying data on the **Overview** page again. | ||
+ | |||
+ | \\ | ||
+ | |||
+ | \\ | ||