====== Overview ======

This page summarizes data needed to verify status, basic configuration settings and hardware specifications. \\ The Overview page is split into sections including System, Ethernet Ports State, WAN, LAN and Wireless.

===== System =====

This section displays hardware specifications and resource usage and information. \\  \\  \\

[[https://wiki.freshtomato.org/lib/exe/detail.php?id=overview&media=pasted:20200520-145618.png|{{:pasted:20200520-145618.png}}]]

 \\


===== Ethernet Ports State =====

Here, icons are shown that represent the Ethernet ports. The LED colours represent link speeds: \\  \\ <fc #4682b4>  BLUE</fc> = 1Gbps\\ <fc #00ff00>GREEN</fc> = 100Mbps\\ <fc #f0e68c>AMBER</fc> = 10Mbps  \\   \\  \\

The inner part of each Ethernet icon turns:\\ Grey for Half-Duplex\\ Black for Full-Duplex

\\ NOTE: The blinking LED colour matches the link speed. However, the LEDs flashing interval is fixed.\\ It doesn't represent the amount of network activity. \\  \\  \\ {{::status-overview-ethenet_ports_state-2024.3.png?679}}

 \\ Clicking the **%%>>%% Configure** button will take you to the [[basic-network|Network]] menu, where you can configure settings for the \\ Ethernet Ports State display.

 \\


===== WAN =====

This shows the WAN status. Information displayed here varies based on the WAN connectivity type (DHCP, PPPoE. etc). \\   \\ **CPU Load:  **the proportion of time (in percent) the CPU is in use for running tasks/executing code.((
CPU Load is in the System section.  CPU Load does **not** equal CPU Utilization.  For more information:  [[https://man7.org/linux/man-pages/man1/uptime.1.html]]
))

 \\

**Status: i**ndicates whether the router is connected to or disconnected from the Internet.

 \\

**Connection Uptime: **how long the router has been connected to the Internet in the current session.

 \\

**Remaining Lease Time:** the time remaining on the WAN port's current DHCP/IP lease.

 \\

**Release**: clicking this disconnects the router from the Internet/WAN.

 \\

**Renew: **clicking this tries to renew the IP lease, and reconnect the router to the Internet/WAN.\\  \\  \\  [[https://wiki.freshtomato.org/lib/exe/detail.php?id=overview&media=pasted:20200520-150153.png|{{:pasted:20200520-150153.png}}]]

 \\


===== LAN =====

The LAN section provides info about FreshTomato's LAN interface.\\  \\  \\  [[https://wiki.freshtomato.org/lib/exe/detail.php?id=overview&media=pasted:20200520-150733.png|{{:pasted:20200520-150733.png}}]]

 \\


===== Wireless (2.4 GHz / ethx) and Wireless (5 GHz/ethy) =====

The Wireless (2.4 GHz /ethx) and Wireless (5 GHz/ethy) section display information and status of the corresponding router interface. Information will vary based on your hardware.

One section is displayed for each frequency band supported by the hardware.

Your FreshTomato device name may be different, depending on the hardware. Device name numbers begin at "0". For example, the first WiFi interface might be eth0, and the second might be eth1.

 \\ \\ [[https://wiki.freshtomato.org/lib/exe/detail.php?id=overview&media=pasted:20200520-151221.png|{{:pasted:20200520-151221.png}}]]

\\ **Enable:**  clicking this turns on the WiFi radio shown under that heading.

This button appears only on some hardware.

 \\

**Disable:**  turns off the WiFi radio under that heading, disconnecting clients.

This appears only on some hardware.

 \\

**Stop:**  clicking this stops sampling data used to update the **Overview** page.

 \\

Choosing an interval rate from the menu and clicking **Refresh** will begin displaying data again. Data are refreshed according to the setting chosen in the Refresh menu.

 \\

 \\