Differences

This shows you the differences between two versions of the page.

--- vpn-tinc [2023/05/26 18:24] – [Hosts Tab] -condense, delete dupe screenshot, formatting hogwild
+++ vpn-tinc [2023/05/26 18:46] – [Hosts Tab] -clarity, condense hogwild
@@ Line 29: / Line 29: @@
 **Ed25519 Private Key: **In this field, enter your private Ed25519 encryption key. This key is needed for the encryption process.
-**RSA Private Key * : **Here, enter your private RSA key. The RSA encryption protocol uses much more CPU power than the Ed25519 protocol. The RSA key is optional and is needed only for communication with hosts using Tinc version 1.0 or lower.
+**RSA Private Key: *  **Here, enter the private RSA key. RSA encryption uses much more CPU power than the Ed25519 protocol. \\ The RSA key is optional and is needed only for communication with hosts using Tinc version 1.0 or lower.
 **Custom: **This field allows you to specify any custom Tinc daemon parameters you might want.  \\   \\
 ===== Hosts Tab =====
-Most of the hosts on your network should be defined on this page. Tinc doesn't need all hosts to be defined. It can use a relay to reach secondary hosts if the end devices can't (yet) communicate. This can be happen for various reasons, including the presence of NAT devices between hosts.
+Most of the hosts on your network should be defined on this page. Tinc doesn't need all hosts to be defined. It can use a relay to reach secondary hosts if the end devices can't (yet) communicate. Hosts may not be able to communicate for various reasons, including the presence of NAT devices between them.
 However, you do need to define "yourself" on each Tinc device.
@@ Line 51: / Line 52: @@
 **Address:  **This is used only when direct communication is possible and defines the IP address or (fully qualified domain name) where the host can be found. Direct communication means without relay.
-**Port:  **An empty value configures the default setting (TCP/UDP, port 655). You might need to tune this for network devices that don't have root/administrator privileges (not applicable to FreshTomato).
+**Port:  **An empty value configures the default setting (TCP/UDP, port 655). You might need to tune this for network devices that don't have root/Administrator privileges (not applicable to FreshTomato).
 **Compression:**  In some cases, compression may increase VPN speeds. The default of "0" (disabled) can be adjusted as high as "11". All nodes must be configured with the same setting. Since most VPN traffic is already compressed at the application layer, think carefully about whether you need this enabled. Enabling compression will add extra workload to the CPU, and may not increase speed/throughput.
@@ Line 59: / Line 60: @@
 **Ed25519 Public Key:**  This is where you enter your Ed25519 encryption Public Key.
-**RSA Public Key: * ** If you're using an RSA key, you must define the public key for each host here. RSA is optional in Tinc versions 1.0 and later.
+**RSA Public Key: * ** If you're using RSA encryption, you must define each host's public key here. RSA is optional in Tinc versions 1.0 and later.
-You must provide minimum information for every host defined before you can click OK and proceed to the next row. Clicking OK **does not** save settings. After you've defined all hosts, and clicked "OK" for each, you must click "Save" at the bottom. Only then will all host settings be saved.
+You must provide minimal information for every host defined before you can click OK and proceed to the next row. Clicking OK **does not** save settings. After you've defined all hosts, and clicked "OK" for each, you must click "Save" at the bottom. Only then will all host settings be saved.
 **Custom:**  In this field, you can define custom settings for each host.

FreshTomato Wiki

User Tools

Site Tools

Differences

Page Tools