FreshTomato Wiki

User Tools

Site Tools

Trace: • wireless_ethernet_bridge
wireless_ethernet_bridge

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
wireless_ethernet_bridge [2023/06/06 20:26] – [Limitations and Workarounds] hogwildwireless_ethernet_bridge [2025/05/12 23:30] (current) – [Wireless Ethernet Bridge Mode] -Change head to: "Configuring Wireless Ethernet Bridge Mode" hogwild
Line 1: Line 1:
-====== Wireless Ethernet Bridge Mode ======+====== Configuring Wireless Ethernet Bridge Mode ======
  
 Wireless Ethernet Bridge Mode is an easy way to expand your network without having to run long Ethernet cable between devices. Wireless Ethernet Bridge Mode is an easy way to expand your network without having to run long Ethernet cable between devices.
Line 20: Line 20:
 ===== Steps ===== ===== Steps =====
  
-For this HOWTO, we will: \\+For this HOWTO, we will: \\  \\
  
   * Refer to the network you want to expand as the "//primary router"// network.    * Refer to the network you want to expand as the "//primary router"// network. 
-  * Refer to the router in Wireless Ethernet Bridge mode as the "//secondary" router//.  +  * Refer to the router in Wireless Ethernet Bridge mode as the \\ "//secondary" router//.  
-  * Use 192.168.1.1 as the primary router address and 192.168.1.2 as the secondary router address. +  * Use "192.168.1.1" as the primary router address and "192.168.1.2" \\ as the secondary router address. 
-  * Perform all steps on the secondary router, (the one you wish to use in Wireless Ethernet Bridge mode).+  * Perform all steps on the secondary router, (the one to use in Wireless \\ Ethernet Bridge mode).
  
  \\  \\
  
-  - First, configure your PC with a static IP address in the same subnet as the secondary router (e.g., 192.168.1.33).\\  +  - Configure your PC with a static IP address in the same subnet as the \\ secondary router (say, "192.168.1.33").\\  \\  
-  - Go to the [[basic-network|Network]] menu//. //In the IP Address field in the LAN section, assign an address in the same subnet  \\ as the primary router, but outside the DHCP pool of your network.  We will use 192.168.1.2. \\ Uncheck the DHCP checkbox and click //OK//. Click Save. \\  +  - Go to the [[basic-network|Network]] menu//. //In the //IP Address// field in the LAN section: 
-  - Log on to the secondary router via 192.168.1.2. In the [[basic-network|Network]] menu//, //configure the settings of the interface that  \\ matches  the primary router WiFi network you want to bridge (2.4GHz or 5GHz) as follows: \\  +    - Enter an IP address in the same subnet as the primary router, \\ but outside the DHCP pool of your network. For our example, \\ we'll use: "192.168.1.2". 
-    * Set Wireless Mode to: Wireless Ethernet Bridge +    - Uncheck the //Use DHCP// checkbox and click //OK//.  
-    * Set Wireless Network Mode to: Auto +    - Click Save. \\  \\ 
-    * Set SSID to: "WlanSSID_to_which_you_want_to_connect_to"  (the primary router's SSID) +  - Log on to the secondary router via 192.168.1.2. In the [[basic-network|Network]] menu//, //\\ configure the settings of the interface that matches the primary router \\ WiFi network you want to bridge (2.4GHz or 5GHz) as follows: \\  \\  
-    * Set Channel to: "Auto" or to match the primary router's setting +    - Set Wireless Mode to: "Wireless Ethernet Bridge". 
-    * Set Channel Width to: match the primary router setting +    - Set Wireless Network Mode to: "Auto". 
-    * Set Control Sideband to: match the setting on the primary router +    - Set SSID to: "WlanSSID_to_which_you_want_to_connect_to"  \\ (the primary router's SSID). 
-    * Set Security to: match the primary router's setting (usually WPA2 Personal) +    - Set Channel to: "Auto" or to match the primary router's setting 
-    * Set Encryption to: match the primary router's setting (usually AES) +    - Set Channel Width to match the primary router setting 
-    * Set Shared Key to: "SharedKey_of_router_to_which_you_want_to_connect"  (the passphrase of the primary router) +    - Set Control Sideband to match the setting on the primary router 
-    * Set Group Key Renewal to: match the primary router setting (usually 3600 seconds) +    - Set Security to match the primary router setting (usually WPA2 Personal) 
-    * Click Save. \\ +    - Set Encryption to match the primary router setting (usually AES) 
-  - In the [[basic-network|Network]] menu, in the LAN section: \\  +    - Set Shared Key to "SharedKey_of_router_to_which_you_want_to_connect"  \\ (the passphrase of the primary router) 
-    * Set Default Gateway to: the IP address of the primary router. We will use 192.168.1.1 +    - Set Group Key Renewal to match the primary router setting \\ (usually 3600 seconds). 
-    * Set Static DNS to: the primary router's IP address. We will use 192.168.1.1 +    - Click Save.\\  \\ 
-    * In **release 2022.6** or later, selecting "Automatic IP" will make your router obtain IP/Gateway/DNS data via DHCP (if possible) +  - In the [[basic-network|Network]] menu, in the LAN section: \\  \\  
-    * Click Save.+    - Set Default Gateway to: the primary router's IP address. \\ We'll use: "192.168.1.1". 
 +    - Set Static DNS to: the primary router's IP address. We'll use: "192.168.1.1". 
 +    - In **release 2022.6** or later, selecting "Automatic IP" will make the router \\ obtain IP/Gateway/DNS data via DHCP (if possible) 
 +    - Click Save.
  
  \\  \\
  
-The process is complete. You should now have a working Wireless Ethernet Bridge.+The process is now complete. You should now have a working Wireless Ethernet Bridge.
  
 Remember to set your computer back to its previous network settings. Remember to set your computer back to its previous network settings.
wireless_ethernet_bridge.1686079581.txt.gz · Last modified: by hogwild

Page Tools

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki