FreshTomato Wiki

User Tools

Site Tools

Trace: • tools-wol • basic-wfilter • tools-survey • admin-config • advanced-access • admin-iptraffic • advanced-vlan • mac_address • enable_disable_ethernet_port • advanced-wlanvifs
advanced-wlanvifs

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
advanced-wlanvifs [2024/10/13 01:03] – [Virtual Wireless Notes] -grammar, condense hogwildadvanced-wlanvifs [2024/11/27 01:34] (current) – [Virtual Wireless Notes and Troubleshooting] hogwild
Line 12: Line 12:
  \\  \\
  
-**Interface: **Here, enter the name you want to give to the wireless VIF (Virtual Interface) in that row.+**Interface: **here, enter the name of the wireless VIF (Virtual Interface) in that row.
  
  \\  \\
  
-**Enabled:  **Checking this enables or disables the VIF in that row.+**Enabled: **checking this enables or disables the VIF in that row.
  
  \\  \\
  
-**SSID:  **Here, enter the the wireless Service Set Identifier of the VIF in that row.+**SSID: **here, enter the the wireless Service Set Identifier of the VIF in that row.
  
  \\  \\
  
-**Mode:  **Here, you can select the wireless interface's mode:+**Mode: **here, you can select the wireless interface's mode: 
 + 
 + \\
  
   * Access Point   * Access Point
Line 39: Line 41:
  \\  \\
  
-**Bridge:**  This allows you to select to which LAN bridge this VIF should be assigned.+**Bridge:**  allows you to select to which LAN bridge this VIF should be assigned.
  
-Virtual wireless networks share the same radio as their corresponding main wireless interface. Thus, to enable any virtual wireless network, the corresponding, shared main interface must be enabled. For example, to enable VIF "wl0.1", the main wireless interface wl0 must be enabled. The opposite is not true. Turning off a corresponding VIF has no effect on the on/off status of the corresponding main interface.+VWLANs share the same radio as their corresponding main wireless interface. Thus, to enable any virtual wireless network, the corresponding, shared main interface must be enabled. For example, to enable VIF "wl0.1", the main wireless interface wl0 must be enabled. The opposite is not true. Turning off a corresponding VIF has no effect on the on/off status of the corresponding main interface.
  
 Physical wireless interfaces are listed as wl0, wl1, wl2, and so on. An alias (like for physical interfaces) is identified by a period (".") and "reference number", such as "wl0.1", "wl0.2" and so on. For example, in the image above, the virtual network "wl0.1" (sharing the 2.4 GHz radio) has SSID name "Guest24". The virtual network "wl0.2" (sharing the 5 GHz radio) has SSID name "Guest50". Physical wireless interfaces are listed as wl0, wl1, wl2, and so on. An alias (like for physical interfaces) is identified by a period (".") and "reference number", such as "wl0.1", "wl0.2" and so on. For example, in the image above, the virtual network "wl0.1" (sharing the 2.4 GHz radio) has SSID name "Guest24". The virtual network "wl0.2" (sharing the 5 GHz radio) has SSID name "Guest50".
Line 49: Line 51:
  \\  \\
  
-**WFilter:**  Here, you can enable/disable MAC address filtering for the VIF on that line, similarly to the [[basic-wfilter|Wireless Filter]] menu.+**WFilter:** here, you can enable/disable MAC address filtering for the VIF on that line.
  
  
-===== Virtual Wireless Notes =====+===== Virtual Wireless Notes and Troubleshooting =====
  
-**Warning!** Avoid using VIFs on an interface that is configured in Wireless Ethernet Bridge or Media Bridge mode. It can cause problems.+**Warning!** Avoid using VIFs on an interface configured in Wireless Ethernet Bridge or Media Bridge mode. It can cause problems.
  
 When you create/define a new wireless VIF (Virtual interface), its MAC Address will be incorrectly shown as: "00:00:00:00:00:00", because it's unknown at that moment. The MAC Address //will// display correctly as soon as the network is restarted and the menu refreshed. When you create/define a new wireless VIF (Virtual interface), its MAC Address will be incorrectly shown as: "00:00:00:00:00:00", because it's unknown at that moment. The MAC Address //will// display correctly as soon as the network is restarted and the menu refreshed.
Line 63: Line 65:
  
 Do not change configuration settings for the primary VIF of any physical wireless interfaces in this menu. For that, use the [[basic-network|Network]] menu. Do not change configuration settings for the primary VIF of any physical wireless interfaces in this menu. For that, use the [[basic-network|Network]] menu.
 +
 + \\
  
  \\  \\
advanced-wlanvifs.1728777803.txt.gz · Last modified: 2024/10/13 01:03 by hogwild

Page Tools

Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki