This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
nas-bittorrent [2022/02/22 15:07] – rs232 | nas-bittorrent [2023/06/04 18:32] (current) – -condense, formatting hogwild | ||
---|---|---|---|
Line 1: | Line 1: | ||
- | ===== Bittorrent | + | ====== BitTorrent |
- | You will find this feature in builds | + | This feature |
- | {{: | + | \\ |
- | ** Enable**: Kicks off the process at every boot, plus runs it as soon as you select Save.\\ | + | |
- | {{: | + | {{: |
- | **Transmission binary path**: Internal/ | + | |
- | {{: | + | \\ **Enable:** |
- | **Click here to open Transmission GUI**: As the name suggests it will open the Transmission | + | |
- | **Keepalive**: | + | |
- | **Check alive every**: The frequency at which the above control should be performed.\\ | + | |
- | **Delay at startup**: For different reasons, but possibly waiting for external storage to be fully up and running, defining a time here in seconds would, as the name suggests, delay the kick off of the process at boot time.\\ | + | |
- | **Listening port**: Define here the port linked to the process. This will be both TCP and UDP.\\ | + | |
- | **Downloading directory**: | + | |
- | **Use incomplete/ | + | |
- | **Autoadd .torrents**: | + | |
- | {{: | + | {{: |
- | **Enable GUI**: This option enables the build in Transmission GUI from where you can administer your download/ | + | |
- | **Listening GUI port**: Define the port where the Transmission administration page should be reachable.\\ | + | |
- | **Authentication required**: It disables anonymous access (strongly suggested) and uses the credentials defined in the below two fields.\\ | + | |
- | **Username**: | + | |
- | **Password**: | + | |
- | **Allow remote access**: If enabled the Listening port becomes reachable also on the WAN side.\\ | + | |
- | {{: | + | \\ **Transmission binary path:** This specifies |
- | **Limits**: The next paragraph " | + | |
- | {{: | + | * Internal - Selecting this means FreshTomato' |
- | **Download queuing**: Is yet another form of limit and controls how many concurrents active Downloads can run simultaneously.\\ | + | * Optware - Choosing this makes FreshTomato use an Optware/ |
- | **Upload queuing**: Same as the option above but applies to Uploads instead.\\ | + | * Custom - Choosing this lets you specify a custom path to the location of the binary.\\ |
- | {{: | + | \\ |
- | **Find more peers using**: Defines on what torrent network type/ | + | |
- | {{: | + | **Click here to open Transmission GUI: |
- | **Message level**: None(0)/Error(3)/Info(6)/Debug(7) - Defines | + | |
+ | **Keepalive: | ||
+ | |||
+ | * **Check alive every: | ||
+ | |||
+ | \\ \\ {{: | ||
+ | |||
+ | **Listening port: | ||
+ | |||
+ | **Downloading directory: | ||
+ | |||
+ | **Use incomplete/: | ||
+ | |||
+ | **Autoadd .torrents: | ||
+ | |||
+ | ===== Remote Access ===== | ||
+ | |||
+ | {{: | ||
+ | |||
+ | **Enable GUI: | ||
+ | |||
+ | * **Listening GUI port: | ||
+ | |||
+ | **Authentication required: | ||
+ | |||
+ | * Username - This specifies your administration username. | ||
+ | * Password - This specifies your administration password. | ||
+ | |||
+ | **Allow remote access: | ||
+ | |||
+ | ===== Limits ===== | ||
+ | |||
+ | The Limits section has settings to define Transmission' | ||
+ | |||
+ | \\ | ||
+ | |||
+ | {{: | ||
+ | |||
+ | ===== Queue torrents ===== | ||
+ | |||
+ | {{: | ||
+ | |||
+ | **Upload queuing: | ||
+ | |||
+ | ===== Advanced Settings ===== | ||
+ | |||
+ | {{: | ||
+ | |||
+ | **Find more peers using: | ||
+ | |||
+ | \\ | ||
+ | |||
+ | {{: | ||
+ | |||
+ | **Message level:** This setting defines the lowest level of Transmission messages to be captured in the system logs | ||
+ | |||
+ | * None (0) - No Transmission messages will be stored in system logs. | ||
+ | * Error (3) - Only error levels and above will be stored in system logs. | ||
+ | * Info (6) - Only Information messages and above will be stored in system logs | ||
+ | * Debug (7) - Debugging level messages and higher will be stored in system logs\\ | ||
+ | |||
+ | \\ | ||
+ | |||
+ | {{: | ||
+ | |||
+ | **Save settings location: | ||
+ | |||
+ | * Download directory - Choosing this stores settings in the Download folder, described above | ||
+ | * JFFS - Selecting this stores settings in [[admin-jffs2|JFFS]] storage that you have already defined. | ||
+ | * CIFS1 - Choosing this stores settings on the first [[admin-cifs|CIFS]] share you've already defined. | ||
+ | * RAM - Choosing this stores settings in RAM. This will not survive a reboot. | ||
+ | * Custom - \\ | ||
+ | |||
+ | \\ | ||
+ | |||
+ | {{: | ||
+ | |||
+ | **Blocklist: | ||
+ | |||
+ | An alternative method you can use is to define the Blocklist in this field to use P2Partisan instead. Using P2Partisan, more lists can be defined. However, to use P2Partisan, you must manually install a script. More details can be found here: [[ https:// | ||
+ | |||
+ | **Custom Log File Path: | ||
+ | |||
+ | **Custom Configuration: | ||
+ | |||
+ | \\ | ||
+ | |||
+ | \\ | ||
- | {{: | ||
- | **Save settings location**: Download directory/ | ||
- | {{: | ||
- | **Blocklist**: | ||
- | **Custom Log File Path**: Define here the location where you want Transmission to log its activity.\\ | ||
- | **Custom Configuration**: |