This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
nas-bittorrent [2023/06/04 17:01] – -condense, grammar hogwild | nas-bittorrent [2023/06/04 18:32] (current) – -condense, formatting hogwild | ||
---|---|---|---|
Line 1: | Line 1: | ||
====== BitTorrent client (Transmission) ====== | ====== BitTorrent client (Transmission) ====== | ||
- | This feature is included in builds that contain Transmission, | + | This feature is included in builds that contain Transmission, |
+ | |||
+ | \\ | ||
{{: | {{: | ||
- | | + | \\ **Enable: |
{{: | {{: | ||
Line 15: | Line 17: | ||
* Custom - Choosing this lets you specify a custom path to the location of the binary.\\ | * Custom - Choosing this lets you specify a custom path to the location of the binary.\\ | ||
- | \\ {{: | + | \\ |
- | **Click here to open Transmission GUI**: This will open Transmission' | + | **Click here to open Transmission GUI:** This will open Transmission' |
**Keepalive: | **Keepalive: | ||
- | **Check alive every: | + | * **Check alive every: |
- | **Delay at startup: | + | \\ \\ {{: |
**Listening port: | **Listening port: | ||
Line 29: | Line 31: | ||
**Downloading directory: | **Downloading directory: | ||
- | **Use incomplete/: | + | **Use incomplete/: |
- | **Autoadd .torrents: | + | **Autoadd .torrents: |
+ | |||
+ | ===== Remote Access ===== | ||
{{: | {{: | ||
- | **Enable GUI: | + | **Enable GUI: |
+ | |||
+ | * **Listening GUI port: | ||
+ | |||
+ | **Authentication required: | ||
+ | |||
+ | * Username - This specifies your administration username. | ||
+ | * Password - This specifies your administration password. | ||
+ | |||
+ | **Allow remote access: | ||
+ | |||
+ | ===== Limits ===== | ||
+ | |||
+ | The Limits section has settings to define Transmission' | ||
+ | |||
+ | \\ | ||
+ | |||
+ | {{: | ||
+ | |||
+ | ===== Queue torrents ===== | ||
+ | |||
+ | {{: | ||
+ | |||
+ | **Upload queuing: | ||
+ | |||
+ | ===== Advanced Settings ===== | ||
+ | |||
+ | {{: | ||
+ | |||
+ | **Find more peers using: | ||
+ | |||
+ | \\ | ||
+ | |||
+ | {{: | ||
+ | |||
+ | **Message level: | ||
+ | |||
+ | * None (0) - No Transmission messages will be stored in system logs. | ||
+ | * Error (3) - Only error levels and above will be stored in system logs. | ||
+ | * Info (6) - Only Information messages and above will be stored in system logs | ||
+ | * Debug (7) - Debugging level messages and higher will be stored in system logs\\ | ||
+ | |||
+ | \\ | ||
+ | |||
+ | {{: | ||
- | **Listening GUI port: | + | **Save settings location: |
- | **Authentication required**: | + | |
+ | | ||
+ | * CIFS1 - Choosing this stores settings on the first [[admin-cifs|CIFS]] share you've already | ||
+ | * RAM - Choosing this stores settings | ||
+ | * Custom - \\ | ||
- | * Username - Define your administration username here. | + | \\ |
- | * Password - Define your administration password here. | + | |
- | **Allow remote access**: If enabled the Listening port becomes reachable also on the WAN side.\\ | + | {{:pasted: |
- | {{: | + | **Blocklist:** |
- | {{: | + | An alternative method you can use is to define the Blocklist in this field to use P2Partisan instead. Using P2Partisan, more lists can be defined. However, to use P2Partisan, you must manually install a script. More details can be found here: [[ https://www.linksysinfo.org/ |
- | {{: | + | **Custom Log File Path:** Here, you define the location where you want Transmission |
- | {{: | + | **Custom Configuration: |
- | {{: | + | \\ |
- | {{: | + | \\ |