Differences

This shows you the differences between two versions of the page.

--- status-overview [2025/08/27 18:26] – [WAN] hogwild
+++ status-overview [2025/08/27 18:32] (current) – [Wireless (2.4 GHz / ethX) and Wireless (5 GHz/ethY)] -Formatting, condense hogwild
@@ Line 22: / Line 22: @@
 The LED colours represent link speeds: \\  \\ <fc #4682b4>  BLUE</fc> = 1Gbps\\ <fc #00ff00>GREEN</fc> = 100Mbps\\ <fc #f0e68c>AMBER</fc> = 10Mbps  \\   \\  \\
-The inner part of each icon turns: \\ \\ Grey for Half-Duplex\\ **Black** for Full-Duplex
+The inner part of each icon turns: \\ \\ Grey = Half-Duplex\\ **Black** = for Full-Duplex
 \\ \\ The blinking LED colour matches the link speed. However, the LEDs flashing interval is fixed-it doesn't reflect the amount of network activity. \\  \\
- \\ Clicking the **%%>>%% Configure** button will take you to the [[basic-network|Network]] menu, where you can configure settings for the Ethernet Ports State display.
+ \\ Clicking %%>>%%** Configure** will take you to the [[basic-network|Network]] menu, where you can configure settings for the Ethernet Ports State display.
  \\
@@ Line 33: / Line 33: @@
 ===== WAN =====
-This shows the WAN status. Information displayed here varies based on the WAN connectivity type (such as DHCP, or PPPoE). \\   \\ **CPU Load:  **the proportion of time (in percent) the CPU is in use for running tasks/executing code.((
+This area displays WAN status details. Information here varies based on the WAN connectivity type (such as DHCP, or PPPoE). \\   \\ **CPU Load:  **the proportion of time (in percent) the CPU is in use for running tasks/executing code.((
 CPU Load is in the System section.  CPU Load does **not** equal CPU Utilization.  For more information:  [[https://man7.org/linux/man-pages/man1/uptime.1.html]]
 ))
- \\
+ \\  \\  {{:pasted:20200520-150153.png}} \\ \\   \\ **Status: i**ndicates whether the router is connected to the Internet.
-{{:pasted:20200520-150153.png}} \\ \\
- \\
-**Status: i**ndicates whether the router is connected to or disconnected from the Internet.
  \\
@@ Line 56: / Line 53: @@
  \\
-**Renew: **clicking this tries to renew the IP lease, and reconnect the router to the Internet/WAN.\\  \\  \\  [[https://wiki.freshtomato.org/lib/exe/detail.php?id=overview&media=pasted:20200520-150153.png|{{:pasted:20200520-150153.png}}]]
+**Renew: **clicking this tries to renew the IP lease, and reconnect the router to the Internet/WAN.
  \\
@@ Line 70: / Line 67: @@
 ===== Wireless (2.4 GHz / ethX) and Wireless (5 GHz/ethY) =====
-The Wireless (2.4 GHz /ethx) and Wireless (5 GHz/ethy) section display information and status of the corresponding router interface. Information will vary based on your hardware.
+These sections display information about and status of the corresponding router interface. Information will vary based on your hardware.
-One section is displayed for each frequency band supported by the hardware.
+One section is displayed for each frequency band supported by the hardware. Your FreshTomato device name may be different.
-Your FreshTomato device name may be different, depending on the hardware. Device name numbers begin at "0". For example, the first WiFi interface might be eth0, and the second might be eth1.
+Device name numbers begin at "0". For example, the first WiFi interface might be eth0, and the second might be eth1.
  \\ \\ [[https://wiki.freshtomato.org/lib/exe/detail.php?id=overview&media=pasted:20200520-151221.png|{{:pasted:20200520-151221.png}}]]
-\\ **Enable:**  clicking this turns on the WiFi radio shown under that heading.
+ \\ \\ **Enable:**  clicking this turns on the WiFi radio shown under that heading.
 This button appears only on some hardware.
@@ Line 86: / Line 83: @@
 **Disable:**  turns off the WiFi radio under that heading, disconnecting clients.
-This appears only on some hardware.
+This button appears only on some hardware.
  \\

FreshTomato Wiki

User Tools

Site Tools

Differences

Page Tools