Differences

This shows you the differences between two versions of the page.

--- tools-wol [2023/05/24 01:48] – [Wake on LAN] -resized screenshot: "pasted 20200524-104525.png" @ 760x564 hogwild
+++ tools-wol [2024/11/06 23:29] (current) – [Wake on LAN Notes and Troubleshooting] hogwild
@@ Line 1: / Line 1: @@
 ====== Wake on LAN ======
-This function allows you a send a Wake-on-LAN signal (also known as a "magic packet") to wired devices on your network to wake them up or power them on.  Wake on LAN is generally not supported by wireless devices.
+This function lets you a send a Wake-on-LAN signal ("magic packet") to wired network devices to wake them/power them on.  Wake-on-LAN is generally not supported by wireless devices. \\   \\   \\ {{:pasted:20200524-104525.png?760}}  \\   \\  \\
 The list of devices on this menu includes:
+ \\
+ \\
   * Devices already active in the ARP table.
-  * Devices defined in a static DHCP assignment.
+  * Devices defined in a DHCP Reservation/Static DHCP assignment.
-  * Devices defined manually in the //Dnsmaq Custom configuration//  field in the Advanced/DHCP/DNS/menu. \\ For example: ''dhcp-host=70:EE:50:37:E8:46,myhostnamein''
+  * Devices defined manually in the //Dnsmaq Custom configuration//  field \\ in the [[advanced-dhcpdns|DHCP/DNS/TFTP]] menu. \\ For example: ''dhcp-host=70:EE:50:37:E8:46,myhostnamein''
- \\
+ \\ Some devices may appear with no defined hostname. You can define one in the //Dnsmasq Custom configuration// field as a workaround.
-Some devices might appear on this menu without their hostname defined/displayed. You can work around this by defining them manually in the //Dnsmasq Custom configuration//  field, as described above.
+\\  \\
-\\ There are two ways to send a magic packet to a device on your network:
+There are two ways to send a magic packet to a network device:
+ \\
+ \\
+  - Click anywhere in the list on the device to wake. The **Wake Up**\\ button briefly will grey out, then return. This indicates a magic packet \\ was just sent to that device's MAC address. \\
+  - Type the desired MAC addresses to wake into the **MAC Address List** box, \\ and then click **Wake Up**. Note that the **Wake Up** button also serves to save\\ the contents of the **MAC Address List** box for future use.
-  - Click anywhere in the list on the device you want to wake. After clicking, the **Wake Up** button briefly will gray out, and then return. This indicates a magic packet was just sent to that device's MAC address.
-  - Type the desired MAC addresses of the devices to be awakened into the **MAC Address List** box, and then click the **Wake Up** button. \\  Note that the **Wake Up** button also serves to save the contents of the **MAC Address List** box to be remembered for future use.
- \\ {{:pasted:20200524-104525.png?760}}
+===== Wake on LAN Notes and Troubleshooting =====
- \\
+For WoL to work, client devices must be configured to respond to magic packets, both in firmware and software.  Enabling the firmware option causes the device's Ethernet chip to remain powered on even when the device is sleeping/off. This allows it to listen for magic packets.  Enabling the software option allows the device to wake up/power on when that packet is received.
  \\
+Most PCs have a Wake-on-LAN option to enable in UEFI/BIOS, named something like:  \\   \\
-===== Wake on LAN Notes =====
-For this function to work on your device, it must be configured to respond to magic packets, both in firmware and in software.  Enabling the firmware option causes the device's Ethernet chip to remain powered on (usually at a low state, like 10 Mbps) even when the device is sleeping or powered off, so it can listen for magic packets.  Enabling the software option allows the device to wake up or power on when the magic packet is received.
-Regarding firmware, most PCs have a Wake-on-LAN option that must be enabled in the UEFI or BIOS, named something like:
   * Power on by PCI-E or PCI   (Asus UEFI)
@@ Line 36: / Line 33: @@
   * Power on by PCI devices     (AMI BIOS)
+ \\
-Regarding software, the Wake-on-LAN settings in a PC's operating system also must be enabled. For details, see:
+You must also enable the WoL settings in your operating system.
-[[https://www.howtogeek.com/70374/how-to-geek-explains-what-is-wake-on-lan-and-how-do-i-enable-it/]]
+For details, see:\\
+ \\
+[[https://www.howtogeek.com/70374/how-to-geek-explains-what-is-wake-on-lan-and-how-do-i-enable-it/|HOWTOGEEK explains what is Wake on LAN and How Do I Enable it?]]
-[[https://docs.microsoft.com/en-us/troubleshoot/windows-client/deployment/wake-on-lan-feature]]
+[[https://docs.microsoft.com/en-us/troubleshoot/windows-client/deployment/wake-on-lan-feature|Microsoft Docs: WoL Behaviour in Windows 10]]
 [[https://wiki.debian.org/WakeOnLan]]
+ \\
+ \\

FreshTomato Wiki

User Tools

Site Tools

Differences

Page Tools